Skip to main content Skip to search Skip to main navigation
Menu

OPTION Fliegl ball slewing ring – U-profile with worm gearing, Outer bolt circle Ø 390 mm; Inner bolt circle Ø 295 mm; Axial load 7.6 t for slewing ring, supplied loose

Description

Scope of delivery

  • 1 × slewing ring with worm gearing, U-profile, outer diameter 435 mm

Note: The hydraulic motor (CLR or CLP series, shaft diameter 25 mm) is ⚠ probably not included in the scope of delivery and must be ordered separately – please confirm with the supplier. Hydraulic hoses and connection fittings are not included.

Technical data

Product typeSlewing ring with worm gearing
DesignU-profile
Outer diameter435 mm
Inner diameter265 mm
Height110 mm
Bolt circles and mounting
Inner bolt circle295 mm / M16
Outer bolt circle390 mm / M16
Load capacity and drive
Axial load7,6 t
Max. rotating load2,5 t
Max. torque (continuous operation)250 daNm
Max. torque (short-term)370 daNm
DriveHydraulic – hydraulic motor, CLR or CLP series
Hydraulic motor shaft diameter25 mm

Product description

What is a slewing ring with worm gearing?

A slewing ring is a bearing that accommodates axial, radial and tilting forces simultaneously – comparable to an oversized ball bearing that also has gearing for the drive. The worm gearing on this slewing ring works as follows: a worm wheel (the gearing on the ring) is driven by a worm shaft (on the hydraulic motor). This principle has three key advantages over a ring gear with pinion drive:

  • Self-locking: Worm gearing holds the load in any position – without a brake or holding valve. The load cannot turn the slewing ring backwards, even if the hydraulic pressure drops.
  • High reduction ratio: A low motor speed produces high torque at the ring – ideal for slow, controlled rotation of heavy loads.
  • Compact design: The motor and worm shaft are positioned beside the ring, not above or below it – keeping the overall height low (110 mm).

7,6 t axial load, 2,5 t rotating load – what does this mean?

The axial load of 7,6 t is the maximum static compressive force that the slewing ring can withstand in the longitudinal (axial) direction – in other words, the weight that can bear vertically on the ring.

The rotating load of 2,5 t is the maximum load the ring can carry while rotating. It is lower than the axial load because additional tilting moments and dynamic forces act during rotation.

Axial load vs rotating load – practical example
SituationRelevant loadLimit
Grab hanging stationary from an excavatorAxial load7,6 t
Grab rotating with a loadRotating load2,5 t
Grab rotating empty (positioning)Rotating loadNot critical
Lateral impact loadRadial load⚠ Not specified

250 daNm torque – how much force is that?

250 daNm (decanewton metres) is equivalent to 2.500 Nm – this is the continuous torque with which the ring can be driven by the hydraulic motor. For short periods (breakaway torque, start-up), 370 daNm (3.700 Nm) is possible.

For comparison: a passenger car diesel engine produces approx. 300–500 Nm. The slewing ring therefore delivers five to eight times the force of a car engine to the rotational movement – but at a very low speed, which is ideal for precise positioning.

Suitable for CLR and CLP hydraulic motors

The slewing ring is designed to be driven by CLR and CLP series hydraulic motors. These orbital motors have a shaft diameter of 25 mm, which engages directly with the slewing ring's worm shaft. The advantage: the hydraulic motor is a standard component – if it wears out, only the motor needs replacing, not the entire slewing ring.

Important: Allow for the hydraulic motor when ordering – it is ⚠ probably not included in the scope of delivery and must be selected to suit the hydraulic system (flow rate, operating pressure).

U-profile – what does this mean?

The U-profile describes the cross-section of the raceway: the balls run in a U-shaped groove that accommodates axial and radial forces simultaneously. Compared with four-point contact bearings, a U-profile is more resistant to edge loading and more tolerant of installation errors – an advantage in the harsh conditions found on construction sites and in forests.

Designed for

  • Excavator attachments: Sorting grabs, demolition grabs and timber grabs – pick up a load, rotate it and place it precisely
  • Forestry equipment: Timber grapples and felling grapples on harvester heads or forwarding cranes
  • Special-purpose machinery: Rotary tables, positioning units and assembly fixtures
  • Recycling and sorting: Sorting grabs on material-handling excavators
  • Municipal equipment: Rotating attachments on municipal vehicles and loader cranes

What this slewing ring does not have – and why

  • No integrated motor: The hydraulic motor is supplied separately. This is not a disadvantage – it allows you to choose the motor freely to suit the hydraulic system (pressure, flow rate, speed).
  • No end stops: The slewing ring rotates continuously – there is no mechanical limit. For applications with a limited rotation angle, end stops must be fitted externally.
  • No rotary union (rotary feed-through): If hydraulic lines need to pass through the slewing ring (e.g. to the grab), a separate rotary union is required.

Frequently asked questions

Why is the rotating load (2,5 t) lower than the axial load (7,6 t)?

The axial load describes pure static compressive loading – the load is stationary. When rotating, dynamic forces come into play: moments of inertia, centrifugal force and, above all, tilting moments caused by an off-centre centre of gravity. This is why the permissible load is lower during rotation. Never exceed either value.

Which hydraulic motor do I need?

An orbital motor from the CLR or CLP series with a 25 mm shaft diameter. The exact motor size depends on the hydraulic system available: flow rate (l/min) determines the speed, while operating pressure (bar) determines the available torque. Please provide the hydraulic specifications of the carrier machine – we will be happy to advise you.

Will the slewing ring hold the load without hydraulic pressure?

Yes. The worm gearing is self-locking: the load cannot turn the slewing ring backwards, even if the hydraulic pressure drops. This is a significant safety advantage over ring gear and pinion systems, which require a holding valve.

Can I also drive the slewing ring electrically?

In principle, yes, provided an electric motor with a 25 mm shaft diameter and suitable torque is used. In practice, hydraulic drive is standard because excavators and cranes already have a hydraulic system. An electric motor may be suitable for stationary applications (rotary tables, assembly fixtures).

How are the bolt circles used?

The inner bolt circle (295 mm, M16) is typically bolted to the stationary part (carrier machine, excavator arm). The outer bolt circle (390 mm, M16) accommodates the rotating attachment (grab, grapple). The arrangement may also be reversed depending on the installation – what matters is the strength grade of the M16 bolts (at least 10.9 recommended).