Skip to main content Skip to search Skip to main navigation
Menu

Nero Mulchraupe funkgesteuert 100 cm, 14 PS, Hangneigung bis 40°

Description

Scope of delivery

  • 1 × radio-controlled flail mower with tracked undercarriage
  • 100 cm mulching unit with 60 blades
  • Petrol engine with manual, electric and remote start
  • 48 V battery, 20 Ah

Please confirm before ordering: the scope of the radio remote control, charger and documentation supplied. The manufacturer does not specify the scope of delivery in detail.

Technical data

BrandNero
TypeRadio-controlled flail mower, tracked undercarriage
Working width100 cm
Cutting height2 to 16 cm
Blades60, 0.2 kg each
Rotor shaftØ 85 mm
EngineLoncin petrol engine
Displacement459 cm³
Power14 hp
Fuel tank capacity6.5 l
Fuel consumptionapprox. 1.6 l/h
Engine oilSAE 15W30 or 15W40, 1.1 l
Gearbox oilSAE 85W-90
StarterManual, electric and remote start
Drive2 electric motors, 1,000 W each, brushless
Generator2,100 W
System voltage48 V
Battery48 V, 20 Ah
Travel speed0 to 4 km/h, continuously variable
Track width150 mm
Maximum slope40°
Radio range500 m
Dimensions1,600 × 1,170 × 770 mm
Weight355 kg
Shipping dimensions1,640 × 1,210 × 900 mm, 415 kg

Product description

This machine solves a problem that conventional equipment cannot: areas too steep for a tractor and too dangerous for a person. Road and railway embankments, dykes, retention basins, pond edges, steep meadows, solar parks and overgrown wasteland.

The operator stands beside the slope and controls the machine by radio. That is the real point—not convenience, but the fact that nobody has to stand up there any more.

40 degrees – putting the figure into context

The permitted slope is 40°, equivalent to an 84% gradient. For comparison:

  • Tractor with rear-mounted mulcher: depending on the machine, the limit is around 25 to 30°
  • Pedestrian-controlled two-wheel tractor: at 40°, the operator would have to stand on the slope and hold a 100 kg machine – practically impossible to control
  • This machine: low centre of gravity, 1.17 m track width, tracked undercarriage, and no operator’s weight moving uphill

What this figure assumes – and this matters: The 40° rating applies to firm ground with good grip. Wet grass, loose soil and leaves on smooth clay reduce the figure considerably, because the limiting factor is then not tipping stability but track grip. Work up and down the slope, not across it, and plan turning areas at the top and bottom. The operating instructions provide the definitive information.

The hybrid drive – the technically interesting feature of this machine

The machine has two separate drive systems, which is what gives it its driving characteristics:

  • The petrol engine drives the mulching unit – 14 hp powering a rotor with 60 blades. This requires mechanical power that a generator of this size could not provide.
  • A 2,100 W generator powers the drive – two brushless electric motors rated at 1,000 W each, buffered by a 48 V, 20 Ah battery.

What this means in practice:

  • Full torque from a standstill. An electric motor delivers maximum pulling power from a standstill. Starting on a 40-degree slope is exactly the situation in which a hydrostatic or mechanical drive reaches its limits.
  • Continuously variable speed from 0 to 4 km/h. Each track is controlled independently – for steering, turning on the spot and manoeuvring with millimetre precision around fences and trees.
  • The combustion engine runs at a constant speed, because it only powers the rotor and generator and does not have to respond to changes in drive load. This results in moderate fuel consumption of 1.6 litres per hour.
  • No hydrostatic drive. No hydraulic oil cooling, no hoses rubbing against the slope, and no oil changes for the drive.

For context: The battery buffers peak loads; it is not a traction battery – the machine cannot run electrically without the engine running. The manufacturer does not state how long the battery can power the machine on its own.

Sixty blades across one metre

The mulching unit uses 60 blades weighing 0.2 kg each on a rotor shaft with an 85 mm diameter.

With a flail mower, it is not the cutting edge that does the work, but the blade’s mass multiplied by its speed. The blade strikes the material rather than cutting it. That is why the number matters: 60 blades across 100 cm provide a dense arrangement that also hits heavier material instead of letting it pass between the flails.

The reinforced 85 mm rotor shaft is designed to withstand the resulting loads: when a blade hits a stone or tree stump, the impact is transferred to the shaft. This is no minor consideration for a machine working in overgrown areas that have not been cleared beforehand.

Allow for wear: blades are consumables. You should keep a full set of 60 in stock – or at least a partial set, as blades break individually and must be replaced in opposing pairs to keep the rotor running smoothly.

Cutting height from 2 to 16 centimetres

The range is unusually wide and covers two different types of work:

  • 2 to 5 cm – maintenance cutting on grassed areas, lawn care on embankments and follow-up mulching
  • 10 to 16 cm – initial maintenance of overgrown areas. A high setting is a form of self-protection here: the rotor passes over stones and stumps instead of hitting them, and the machine works its way down in several passes.

For unfamiliar areas, start high and work down gradually. A set of blades costs more than making a second pass.

Remote control with a range of 500 metres

The radio range is 500 m – considerably more than is needed to control the machine visually on a slope. This is deliberate: the extra range provides a buffer against signal obstruction from vegetation, buildings and changes in terrain; it is not an invitation to work from 500 m away.

The machine should be operated within sight. The operator must be able to see what is in front of the machine and where the mulch is being discharged – towards the road, vehicles or people.

The machine can be started remotely, as well as by manual or electric start. This is useful on a slope: if the engine stalls at the top, nobody has to climb up.

Tracked undercarriage with 150 mm-wide tracks

The tracked undercarriage has two functions: traction on slopes and weight distribution. At 355 kg, the machine exerts considerably less ground pressure on two tracks than it would on four wheels – it leaves no ruts on maintained areas.

To be clear: 150 mm are narrow tracks. This is the right size for firm ground and grass. On very soft, wet ground and loose sand, narrow tracks reach their limits sooner than wide ones – in those conditions, grip matters more than the slope angle.

What the machine replaces – and what it does not

It replaces: brushcutter work on steep slopes, manual work on embankments, the tractor in places it cannot reach, and the risk that someone previously had to take.

It does not replace: a tractor-mounted mulcher on large, accessible areas. With a 1 m working width and a speed of 4 km/h, the theoretical area output is around 0.4 ha/h – considerably less in practice, because the machine travels more slowly on slopes and each pass has to be started individually. This machine makes economic sense because of its accessibility and safety, not its hectares per hour.

Transport and handling

At 355 kg net weight and 415 kg shipping weight, this is not something you can simply put on a car trailer. For transport to the work area, allow for a trailer with loading ramps or a tail lift – and bear in mind that the machine can drive itself up, making loading easier.

Frequently asked questions

How steep can the slope be?

The manufacturer specifies 40°, equivalent to an 84% gradient. This rating assumes firm ground with good grip. On wet grass, loose soil or leaves on clay, the limiting factor is not tipping stability but track grip. Work up and down the slope, not across it; the operating instructions provide the definitive information.

How does the drive work?

There are two separate drive systems: the petrol engine drives the mulching unit, while a 2,100 W generator powers two brushless drive motors rated at 1,000 W each in a 48 V system, buffered by a battery. This provides full torque from a standstill, continuously variable travel from 0 to 4 km/h and independent control of each track.

Can the machine run on electricity alone?

No. The 48 V, 20 Ah battery buffers peak loads; it is not a traction battery. The combustion engine must be running. The manufacturer does not state how long the battery can power the machine on its own.

What area output can the machine achieve?

The theoretical figure is around 0.4 ha/h with a 1 m working width and a speed of 4 km/h – considerably less in practice, as work is carried out more slowly on slopes. This machine makes economic sense because of its accessibility and safety, not its hectares per hour.

What is the radio range?

500 m. The range provides a buffer against signal obstruction from vegetation and changes in terrain – the machine should be operated within sight, as the operator needs to see what is in front of the machine and where the mulch is being discharged.

Which cutting height should I choose?

2 to 5 cm for maintenance cutting on grassed areas, and 10 to 16 cm for the initial maintenance of overgrown areas. On unfamiliar ground, start high and work down gradually – the rotor will then pass over stones and stumps instead of hitting them.

How many blades does the mulching unit have, and are they wear parts?

60 blades weighing 0.2 kg each on a reinforced rotor shaft with an 85 mm diameter. Blades are consumables. They break individually and should be replaced in opposing pairs to keep the rotor running smoothly.

How much fuel does the machine use?

Around 1.6 litres per hour with a 6.5 l fuel tank – enough for around four hours of work. Fuel consumption is moderate because the engine runs at a constant speed and does not have to respond to changes in drive load.

How is the machine transported?

At 355 kg net weight, it needs a trailer with loading ramps or a tail lift. The machine can drive itself up, making loading easier. The shipping weight is 415 kg on a pallet.