MX Kombigreifer Teleskoplader 2500 mm, 11 Gabel- und 9 Greiferzinken
€5,338.20
Scope of delivery
- 1 × combination grab, width 2.500 mm
- Manure fork with 11 tines in cross-section, Ø 45 × 1.000 mm
- Grab with 9 flat tines, Ø 35 mm
- Coupling for your tool carrier – included as standard
Please specify when ordering: Make and model of your telehandler. The attachment is supplied with the coupling for the original tool carrier; alternative mounts are available on request.
Options: MACH-2 quick coupler, tongue, special colour.
Technical data
| Manufacturer | MX (Mailleux), France |
|---|---|
| Type | Combination grab, manure fork with hydraulic grab |
| Range | Medium |
| Width | 2.500 mm |
| Fork tines | 11 |
| Grab tines | 9, flat design |
| Fork tines | Cross-section, Ø 45 × 1.000 mm, high-strength cast material |
| Grab tines | reinforced, Ø 35 mm |
| Grab opening | 90° |
| Unladen weight | 735 kg |
| Coupling | bolted, supplied as standard for the original tool carrier |
| Carrier machines | Telehandlers and TX400 loaders |
| Not suitable for | self-propelled machines |
Product description
A combination grab is a manure fork with a hydraulic hold-down: the tines enter the material, the grab comes down from above, and the load is clamped rather than simply carried. With a 2.50 m width and 11 fork tines, this attachment is designed for high throughput – clearing out the barn, loading the manure pad and filling the spreader.
Eleven fork tines across 2.50 metres
The number of tines is an often-overlooked specification for a manure fork. Eleven tines across 2.500 mm give a spacing of around 23 cm – close enough to retain strawy manure and silage, but far enough apart for the material to release when tipped rather than getting caught.
The tines are 1.000 mm long, 45 mm in diameter and have a cross-section, made from high-strength cast material in a heavy-duty design.
Why the profile matters: When a tine enters the material, it is subjected to bending not only upwards but also sideways – for example, when it hits a matted layer of manure or a compacted edge. A cross-section withstands bending in both planes; a round tine is equally weak in every direction. At 2.50 m wide and fully loaded, these are the forces that determine its service life.
The high-strength cast material addresses the second problem: wear at the tine tip. Manure on concrete is abrasive, and a tine that wears round will no longer penetrate – it will push.
Nine flat grab tines – and when the other design is better
This attachment has nine grab tines in a flat design. MX also offers the same size with 12 tines at the front plus 4 at the sides – at almost the same price and with an additional 25 kg of weight.
When the nine flat tines are the right choice: for long-fibred, strawy manure and silage. The material interlocks, so the grab only needs to hold it down. Fewer tines mean less resistance when entering the material and less material getting caught when opening – anyone handling strawy manure every day will work faster with this design.
When the 12 + 4 tine design is better: for short, free-flowing material – settled manure without straw, finely chopped silage, plant residues and substrates. The four side tines close off the sides of the grab, precisely where a grab with open sides loses its load.
At virtually the same price, this is a question of material, not cost. Consider what you load most often.
The grab opens to 90 degrees
A grab that opens only 60 or 70 degrees limits the filling height – it comes down onto the material before the fork is full, leaving the operator with a half load.
At 90 degrees, the grab stands vertically and clears the entire loading space: a full load on every trip, and therefore fewer trips per trailer. The wide opening also allows you to handle square bales occasionally – it is no substitute for a bale grab, but saves changing attachments when a few bales come up during the job.
The Medium range – and when the larger version would be the right choice
| Medium (this attachment) | High | |
|---|---|---|
| Unladen weight | 735 kg | 790 kg |
| Dimensions | 930 / 1.000 / 1.500 mm | 1.130 / 1.200 / 1.700 mm |
| Carrier machines | Telehandlers and TX400 loaders | telehandlers only |
The Medium version is 55 kg lighter and more compact – directly increasing the available payload of your machine. It is also approved for TX400 loaders, unlike the High range.
The High version is worthwhile if you handle very large volumes at height and need the additional 20 cm of grab geometry – for example, when loading high-sided spreaders or containers.
The coupling is included
The attachment is supplied as standard with the coupling for your original tool carrier. This is not a given with telehandlers: there is no universal standard, and many manufacturers require the mount to be ordered separately.
Couplings are available for, among others, Manitou, JCB Quick Fit, JCB Tool Carrier, Merlo, Kramer Scorpion, Dieci, Caterpillar, Deutz Agrovector, Volvo, Schäffer, Bobcat, Weidemann, Zettelmeyer and Euronorm. Approval is granted for each carrier model, not each brand – please specify the make and model of your loader when ordering.
As the coupling is bolted, the following applies: if you change machines later, you replace the coupling, not the attachment.
The MACH-2 quick coupler
The optional MACH-2 plug is a drip-free quick coupler for the hydraulic connection between the telehandler and the attachment.
- Time. All the lines connect in one movement, instead of coupling each plug individually. For an attachment that is changed several times a day, this is the biggest time-saver in the accessories range.
- No drips. No oil stains in the yard, no oily hands, no oil loss.
Important: TX400 loaders are fitted with a MACH-2 housing as standard. If you operate one of these machines, order the matching plug for the attachment at the same time – otherwise the existing quick coupler will go unused.
When a combination grab is the right attachment
Compared with a simple manure fork: The grab holds the load. Nothing falls off on the way from the barn to the trailer, and material can be discharged precisely when loading a spreader. Anyone using an open fork will have to sweep the yard afterwards.
Compared with a closed bucket: The fork penetrates matted material, while a bucket pushes it ahead. In an established manure mat, that is the difference between getting on with the job and merely making a start.
To be honest, when it is not suitable: A fork is the wrong tool for loose, free-flowing bulk materials – sand, grain and woodchips – because the material trickles through between the tines. You need a bucket for those.
Frequently asked questions
Is the mount included in the scope of delivery?
Yes. The attachment is supplied as standard with the bolted coupling for your original tool carrier. Please specify the make and model of your loader when ordering – alternative mounts are available on request.
Will the combination grab fit my telehandler?
Couplings are available for, among others, Manitou, JCB Quick Fit, JCB Tool Carrier, Merlo, Kramer Scorpion, Dieci, Caterpillar, Deutz, Volvo, Schäffer, Bobcat, Weidemann and Euronorm. This attachment is also approved for TX400 loaders. Approval is granted for each carrier model, not each brand. It is not approved for self-propelled machines.
What is the difference compared with the version with more grab tines?
This version has 9 flat grab tines, while the other has 12 at the front plus 4 at the sides and weighs 25 kg more, at almost the same price. The nine tines are suited to long-fibred, strawy manure and silage and penetrate more easily; the version with side tines holds short, free-flowing material better because the sides of the grab are closed.
What does a 90-degree grab opening offer?
The grab stands vertically and clears the entire loading space. The fork can be filled to capacity, rather than the grab coming down onto the material too soon. It can also be used to handle square bales occasionally.
Why do the fork tines have a cross-section?
Because when a tine enters the material, it is subjected to bending not only upwards but also sideways – for example, in a matted layer of manure. A cross-section withstands bending in both planes; the high-strength cast material provides wear resistance at the tip.
What is the difference between the Medium and High ranges?
At the same width, the Medium version is 55 kg lighter and more compact (930/1.000/1.500 mm compared with 1.130/1.200/1.700 mm) and is also approved for TX400 loaders. The High version offers more grab geometry for handling loads at height.
What is the MACH-2 quick coupler for?
It connects all the hydraulic lines in one movement, without drips. This saves time every time you change attachments and prevents oil loss. TX400 loaders come with the MACH-2 housing as standard – the matching plug for the attachment should be ordered at the same time.
Can I use it to load sand or grain?
No. Loose, free-flowing material trickles through between the tines. A bucket is the right tool for bulk materials.
What is the advantage over a simple manure fork?
The grab holds the load. Nothing falls off on the way to the trailer, and material can be discharged in a controlled manner when loading a spreader.
| Cultivation method: | Aufnahme Teleskoplader |
|---|---|
| Einsatzklasse: | Medium |
| Gerätetyp : | Greifschaufel und Greifer |
| Working width: | 2.50m |