Skip to main content Skip to search Skip to main navigation
Menu

Kolbenkompressor 50 l, 8 bar, 240 l/min, 2 kW, 230 V, fahrbar

Skip product gallery

Zubehör

Kompressoröl, 5-Liter-Kanister, grauer Kunststoffkanister, Schraubverschluss, GRANIT VRL 100
Compressor oil VCL 100 5l
Prod. no.: GRA-21088898 GEB5
Hersteller:

Regular price: €39.22
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Compressor oil, 5 liters - according to DIN 51506 (VDL, formerly VCL 100)
Compressor oil, 5 liters - according to DIN 51506 (VDL, formerly VCL 100)
Prod. no.: SW34701
Hersteller:

Available, delivery time: 1-3 days

Regular price: €46.67
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Compressor oil VCL 100 - 20L canister
Compressor oil VCL 100 - 20L canister
Prod. no.: GRA-21088898 GEB20
Hersteller:

Available, delivery time: 1-3 days

Regular price: €134.45
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Description

Scope of delivery

  • 1 × mobile piston compressor

Important: The compressor is supplied dry – compressor oil must be ordered separately.

Technical data

FeatureValue
Product typeMobile, wheeled piston compressor
DesignTwin-cylinder, single-stage
Number of cylinders2
Stages1
Intake capacity240 l/min
Tank capacity50 litres
Tank pressure8 bar
Motor power2 kW
Compressor speed1.100 U/min
Mains connection230 V / 50 Hz
Dimensions L × W × H940 × 420 × 700 mm
Weight73 kg
Delivery conditiondry – order oil separately
Type of usenot for continuous use, observe duty cycle

Product description

Mobile piston compressor with 50-litre tank and twin-cylinder compressor unit

This mobile, wheeled piston compressor delivers an intake capacity of 240 l/min at a tank pressure of 8 bar – designed for workshops, farms and building sites.

Twin-cylinder design – why two instead of one

The compressor unit operates with two cylinders in a single-stage design. Both compress in parallel to the final pressure.

The advantages over a single-cylinder unit of the same output:

Smoother running. Two pistons working in opposite directions balance out some of the inertial forces – the unit vibrates considerably less and does not move around.

More even delivery. Pressure pulses occur at shorter intervals, making the flow rate more consistent.

Lower thermal load per cylinder. The work is shared – each cylinder runs cooler than a single cylinder that would have to deliver the same volume.

Lower operating speed possible. At 1.100 U/min, the compressor unit runs slowly – this means less wear, less heat and noticeably lower noise levels than with high-speed direct drives.

Intake capacity of 240 l/min – putting it into perspective

The intake capacity is the volume of air drawn in by the compressor unit – not the volume actually delivered.

The reason: due to compression losses, heating and internal backflow, the effective delivery rate is typically considerably lower – usually around 60 to 70 per cent for piston compressors of this design.

In practice, this means: The figure is useful for comparing units, but not for directly sizing a tool. If you want to operate a tool with a high continuous air demand, compare the tool's air consumption with the delivery rate – not the intake capacity.

What 240 l/min is enough for

Well suited to: inflating tyres, blowing out, nail guns and staplers, spray guns for hobby and repair work, impact wrenches used intermittently, chiselling hammers for short periods, paint spraying.

Borderline: air sanders, sandblasting equipment and grinding machines – these tools continuously consume air and empty the tank faster than it can be refilled.

50-litre tank – the buffer effect

The tank acts as a buffer between the compressor unit and the tool. It allows short bursts of air consumption that exceed the delivery rate.

Fifty litres is a suitable capacity for the applications described: large enough for typical intermittent use, yet small enough to keep the unit manageable.

The practical effect: An impact wrench that draws more air than the compressor unit delivers for ten seconds will still work – the tank makes up the difference and refills during the break.

Not for continuous use – observe the duty cycle

The manufacturer expressly states: The compressor is not designed for continuous use.

This is not a limitation in quality, but the design specification for this category of equipment. Piston compressors of this design operate intermittently – in cycles – typically with a duty cycle of around 50 per cent.

What this means in practice:

The compressor unit needs breaks to cool down. If it runs continuously, the cylinder head overheats, the oil loses its lubricating properties and wear increases dramatically.

Intermittent operation is the norm: fill the tank, use the tool, then let the compressor top it up.

Anyone needing a continuous air supply – for example, for sandblasting or grinding – needs a compressor with a higher duty cycle or a screw compressor.

Take this information seriously before buying – it determines whether the unit is suitable.

8 bar tank pressure

Eight bar covers the standard requirements of virtually all air tools that typically operate at a working pressure of 6 to 6.3 bar.

The reserve is intentional: there are pressure losses in the lines, resistance at the couplings and a pressure drop when air is drawn off. A tank that only fills to working pressure would provide no usable buffer.

Set the working pressure at the pressure regulator – each tool has its own specified pressure.

230 V – the connection advantage

Two kilowatts from a standard socket. No three-phase connection required.

For workshops without a three-phase supply, use at different locations and domestic applications, this is often the deciding factor.

Please note: Compressors have a high starting current. Long extension leads or circuits with low-rated fuses may cause the fuse to trip. Keep extension leads as short as possible and use a sufficient cable cross-section.

Wheeled – 73 kg and easy to move

At 73 kg, being wheeled is not just a convenience – it is essential for practical use. Without wheels, moving it would be a two-person job.

At 940 mm long and 420 mm wide, the unit is also narrow enough to fit through standard doors and passageways.

Supplied dry – the most important point before commissioning

The compressor is supplied dry. Compressor oil must be ordered separately.

This is not a minor detail, but the most critical point when commissioning the unit. Starting the compressor without filling it with oil will destroy it within minutes: the pistons, cylinders and bearings will run without a lubricating film and seize.

Why it is supplied dry: Oil deteriorates over time, can leak during transport and storage, and the right type may vary depending on the operating conditions.

Before first use:

  1. Order compressor oil separately – the manufacturer recommends a special compressor oil.
  2. Fill with oil as instructed in the operating manual, and check the level through the sight glass.
  3. Do not use engine oil – compressor oil has a different additive package and different coking properties.

Points to note

Fill with oil before first use – the compressor is supplied dry.

Observe the duty cycle. Not designed for continuous use.

Check the oil level regularly and observe the oil change intervals.

Drain condensate daily. Moisture in the air condenses in the tank during compression. If water is left in the tank, it will rust from the inside – the most common cause of compressor failure and a safety risk, as a corroded pressure vessel can burst.

Keep the intake filter clean. A clogged filter reduces performance and increases the temperature.

Ensure adequate ventilation. The compressor needs cooling air; do not operate it in confined spaces.

Do not adjust or block the safety valve.

Before carrying out maintenance unplug the mains lead and fully depressurise the tank.

Personal protective equipment: wear hearing protection during prolonged operation and safety glasses when working with compressed air.

Never direct compressed air at people or use it to blow out clothing – compressed air can penetrate the skin and enter the body.

Pressure vessels are subject to inspection requirements. Depending on their size and pressure, compressed-air vessels must undergo periodic inspections; the applicable requirements are set out in the German Industrial Safety Regulation and relevant DGUV regulations.

Typical applications

Workshops and maintenance shops, car and agricultural machinery repairs, tyre inflation and blow-out work, nail guns and staplers in timber construction, spray painting and paint spraying, farms and agriculture, building sites and mobile applications, gardening and landscaping, home workshops and hobby use, club premises and shared workshops.

Frequently asked questions

What are the benefits of the twin-cylinder design?
Smoother running thanks to partial balancing of inertial forces, more even delivery, lower thermal load per cylinder and the option of a lower operating speed – at 1.100 U/min, the compressor unit runs slowly, reducing wear, heat and noise.

What does an intake capacity of 240 l/min mean?
The volume of air drawn in by the compressor unit – not the volume delivered. Compression losses and heating make the effective delivery rate considerably lower, typically around 60 to 70 per cent for this design. The delivery rate, not the intake capacity, is the key figure when sizing a tool.

Which tools is the compressor suitable for?
Well suited to inflating tyres, blowing out, nail guns and staplers, spray guns, impact wrenches used intermittently and chiselling hammers for short periods. Air sanders and sandblasting equipment are borderline – they consume air continuously.

Why is the compressor not suitable for continuous use?
Piston compressors of this design operate intermittently – typically with a duty cycle of around 50 per cent. The compressor unit needs breaks to cool down; if it runs continuously, the cylinder head overheats, the oil loses its lubricating properties and wear increases dramatically.

What is the 50-litre tank useful for?
It acts as a buffer between the compressor unit and the tool. An impact wrench that briefly draws more air than the compressor unit delivers will still work – the tank makes up the difference and refills during the break.

Why an 8 bar tank pressure if tools operate at 6 bar?
The reserve is intentional: there are pressure losses in the lines, resistance at the couplings and a pressure drop when air is drawn off. Set the working pressure at the pressure regulator.

Do I need a three-phase supply?
No, 230 V is sufficient. Please note: compressors have a high starting current – keep extension leads as short as possible and use a sufficient cable cross-section.

Do I need to do anything before commissioning?
Yes, absolutely: the compressor is supplied dry. Compressor oil must be ordered separately and added before starting the unit for the first time. Starting it without oil will destroy it within minutes.

Can I use engine oil?
No. Compressor oil has a different additive package and different coking properties. The manufacturer recommends a special compressor oil.

What is the most important maintenance task?
Drain condensate daily. Moisture in the air condenses in the tank during compression – if water is left there, the tank will rust from the inside. This is the most common cause of failure and a safety risk, as a corroded pressure vessel can burst.

How do I move the unit?
Use the wheels. At 73 kg, moving it without wheels would be a two-person job; at 940 × 420 mm, it fits through standard doors.

Properties
Abmessungen L x B x H (mm): 940 x 420 x 700
Ansaugleistung (l/min.): 240
Artikelart: Druckluft, Kolbenkompressoren
Benennung: Twin Kolbenkompressor
Elektronischer Anschluss (V/Hz): 230 / 50
Kesseldruck (bar): 8
Kesselgröße (Liter): 50
Motorleistung (KW): 2
Product group: Drucklufttechnik, Werkstattbedarf
Speeds: 1
Verdichterdrehzahl (U/min): 1100
Version: • Kolbenkompressor • mobil • verfahrbar
Weight (kg): 73
Zylinderzahl: 2