Fliegl sweeper broom »Löwe«, 4000 mm, 8 brush rows
€4,300.00
Equipment
- Combined Euro and forklift mounting as standard
- Sweeping brush with 8 rows of plastic bristles, bristle height 255 mm
- Polyurethane skid for height adjustment
- Very robust support frame
- Galvanised finish
Technical data
| Manufacturer | FLIEGL |
|---|---|
| Product type | Attachment sweeper without drive |
| Working width | 4.000 mm |
| Rows of bristles | 8 |
| Bristle material | Plastic |
| Bristle height | 255 mm |
| Mounting | Euro and forklift, combined |
| Forklift pocket dimensions, internal | 195 × 80 mm |
| Height adjustment | Polyurethane skid |
| Drive | not required |
| Hydraulic connections | not required |
| Surface protection | galvanised |
| Maintenance | maintenance-free |
| Weight | approx. 260 kg |
Product description
Sweeper without drive – sweeping and pushing in a single operation
The galvanised sweeper is ready for use in just a few minutes, as no hydraulic connections are required. The quick-attach system allows it to be attached and detached quickly, while the wide support surfaces improve ground tracking.
No drive – that is the key feature
This is what fundamentally distinguishes the brush from a rotary sweeper.
| Sweeper without drive | Rotary sweeper | |
|---|---|---|
| Hydraulic connection | not required | required |
| Set-up time | a few minutes | connect hoses |
| Dust generation | low | considerable |
| Maintenance | maintenance-free | hydraulic motor, bearings, drive |
| Purchase cost | significantly lower | higher |
| Carrier vehicles | virtually all | only with an auxiliary hydraulic circuit |
| Sweeping performance on compacted dirt | limited | better |
How the brush works: The bristles are pulled or pushed across the surface – the sweeping action is created by the vehicle's movement.
Who this is the right solution for:
- Vehicles without a spare auxiliary hydraulic circuit – often the case with yard loaders and telescopic handlers.
- Forklift operation – hydraulic connections on the mast are rarely available.
- Occasional use – when a rotary sweeper is not cost-effective.
- Loose materials – soil, sawdust, silage, bark mulch.
Where its limits lie: A non-powered brush cannot match a rotary sweeper when dealing with compacted dirt, moss and dried-on material. For loose material, however, it is the more efficient solution.
Sweep up without creating dust
This is an advantage that is often underestimated.
Why rotary brushes create dust: The bristles strike the ground at high speed and stir up fine particles. Much of the dust ends up in the air rather than in the swept material.
This does not happen with a pulled brush: The bristles skim across the surface and push the material together.
Where this makes a difference:
- In sheds and livestock buildings – dust settles on machinery, feed and equipment.
- Near homes – dust clouds on neighbouring properties cause problems.
- When handling feed – dust means material loss and contamination.
- For the health of employees.
Sweep and push at the same time – especially for winter maintenance
The manufacturer describes this combination.
What this makes possible: With a push blade mounted at the front, the snow is pushed away while the brush behind it sweeps up the remaining snow.
Why this makes a difference in winter maintenance: A push blade always leaves a thin layer behind – and that is exactly what turns into ice in freezing conditions.
What would otherwise be needed: a second pass with the brush – or gritting salt to break down the remaining layer. Both cost time or money.
The added benefit: Less residual snow means less salt is needed – saving costs and protecting the surroundings.
Important when combining attachments: The levelling blades listed as accessories are available for widths of 2.000, 2.500 and 3.000 mm. Availability for the 4.000-mm version should be confirmed in advance.
The combined Euro and forklift mounting
Both systems are fitted to the same frame as standard.
| Mounting | Carrier vehicle |
|---|---|
| Euro | Front loaders, yard loaders, wheel loaders |
| Forklift | Forklifts, telescopic handlers with forks |
What this means in practice: One implement for two types of vehicle. The brush can be moved between a yard loader and a forklift without changing the mounting.
The internal forklift pocket dimensions are 195 × 80 mm – check this against the existing fork tines.
This is a real advantage for businesses with a mixed fleet – and an implement with two mounting options will appeal to more buyers when resold.
The polyurethane skid
It adjusts the height of the rows of bristles.
Why contact pressure is crucial:
- Too little pressure: The bristles barely touch the ground – fine dirt is left behind.
- Too much pressure: The bristles bend over and drag on their sides – wear increases dramatically and sweeping performance drops.
- Correctly adjusted: The tips of the bristles skim the ground.
What else the skid does: It compensates for bristle wear. As the bristles get shorter, the height can be readjusted – keeping sweeping performance constant until the end.
Why polyurethane: The material glides easily, wears slowly and leaves no marks on concrete or paving – unlike a steel skid, which can score the surface.
8 rows of bristles with a height of 255 mm
The brush depth is the feature highlighted by the manufacturer.
Why multiple rows in succession make a difference: Each row picks up what the previous one has left behind.
- With a single row coarse dirt bounces over the bristles.
- With several rows it is caught by the next row.
- Uneven surfaces are compensated for – where one row does not make contact, the next one does.
The manufacturer describes this as “the best sweeping performance, even on uneven surfaces” – and that is exactly the point.
The 255 mm bristle height also provides a wear reserve: the bristles wear down and the height can be readjusted using the skid.
Galvanised – the right corrosion protection
The entire brush is galvanised.
Why this is necessary for a sweeping implement:
- Damp swept material gets caught between the rows.
- During winter maintenance gritting salt is added – one of the most corrosive substances of all.
- With silage and manure acidic and ammonia-containing residues have an effect.
- The implement is often left outdoors.
How galvanising differs from painting: The zinc coating also protects scratches and edges – it provides cathodic protection, including where the coating itself has been worn away.
Scratches are inevitable on an implement that is constantly dragged across the ground.
Smooth surfaces for cleaning
A detail with practical value.
Why it matters: Material collects between the rows of bristles – especially damp silage, manure and compost.
What happens with a complex design: The material dries on and is difficult to remove. It is carried over when switching to the next material – an important consideration when sweeping manure and then feed.
Maintenance-free
The manufacturer states this explicitly.
Why this is possible: There is no drive, gearbox, hydraulics or bearings under load. The only wear parts are the bristles and skid.
What this means in operation: No greasing, no oil changes, no seals. The implement can stand idle for eleven months and still work in the twelfth.
Suitable materials
- Garden waste and compost
- Soil
- Sawdust and wood shavings
- Sand and fine bulk materials
- Silage
- Bark mulch
- Snow and residual snow
What these materials have in common: They lie loose on the surface. For this, a non-powered brush is the most efficient solution.
4.000 mm working width – covering large areas
At 4 m wide, large areas can be covered in just a few passes.
The calculation: A 20 m-wide shed can be swept in five passes – at 2.5 m wide, it would take eight.
Please note: 4 m exceeds the permitted vehicle width. For travel on public roads, comply with the requirements for width, marking and lighting.
Additional accessories
| Accessory | Note |
|---|---|
| Bale clamp mounting | additional mounting option |
| Wheel loader or telescopic handler mounting | additional mounting option |
| Bucket mounting | additional mounting option |
| Grapple bucket mounting | additional mounting option |
| Steel bristles, 270 mm | for industrial use |
| Rigid tipping bucket, pendulum-mounted | only for 2.000, 2.500 and 3.000 mm |
| Levelling blade with PU scraper bar | only for 2.000, 2.500 and 3.000 mm |
| Levelling blade with HB-500 scraper bar | only for 2.000, 2.500 and 3.000 mm |
About the steel bristles: They are intended for industrial use – more aggressive sweeping, but not suitable for delicate surfaces. Plastic bristles remain the right choice for paving and coated concrete.
The brush is available on request with additional mounting options and in other widths.
Applications
Farms and farmyards, biogas plants and silage clamps, storage and production sheds, local authorities and depots, winter maintenance, sawmills and woodworking businesses, composting facilities, equestrian centres, commercial and logistics areas.
Operating notes
- Check the mounting: Euro or forklift; internal forklift pocket dimensions 195 × 80 mm.
- Check the load capacity of the carrier vehicle – 260 kg acts at the attachment point.
- Set the contact pressure correctly using the skid – excessive pressure dramatically increases bristle wear without improving the result.
- Readjust the skid as the bristles wear.
- Use plastic bristles on delicate surfaces; steel bristles are intended for industrial use.
- Watch out for manhole covers, drainage channels and loose paving stones.
- When travelling on roads, comply with the requirements for width, marking and lighting – 4 m exceeds the permitted vehicle width.
- Do not enter the working area.
- Dispose of swept material properly.
- Remove material from between the rows of bristles after use – dried-on material is difficult to remove and will be carried over.
- After winter maintenance, rinse with clean water – gritting salt residues can also attack galvanised surfaces during storage.
- Check the bristles regularly for wear.
Frequently asked questions
Do I need a hydraulic connection?
No. The brush operates without hydraulic or mechanical drive – the sweeping action is created by the vehicle's movement. It is ready for use in just a few minutes.
Which vehicles is the brush compatible with?
As standard, it fits front loaders with a Euro mounting and forklifts. The internal forklift pocket dimensions are 195 × 80 mm. Other mounting options are available as accessories.
Does the brush create dust when sweeping?
Significantly less than a rotary sweeper. The bristles skim across the surface and push the material together instead of stirring it up.
Can I also use it to clear snow?
Yes. With a push blade mounted at the front, the snow is pushed away while the brush sweeps up the remaining snow – precisely the layer that would otherwise turn into ice.
How is the height adjusted?
Using a polyurethane skid. It also compensates for bristle wear, keeping sweeping performance constant.
What maintenance is required?
None. The brush is maintenance-free – there is no drive, gearbox or hydraulics. The wear parts are the bristles and skid.
What is the brush suitable for?
For loose material: garden waste, compost, soil, sawdust, sand, fine bulk materials, silage and bark mulch. It cannot match a rotary sweeper when dealing with compacted dirt.
Are steel bristles available?
Yes, with a length of 270 mm for industrial use. Plastic bristles remain the right choice for delicate surfaces such as paving and coated concrete.
| Anzahl Besenreihen: | 8 |
|---|---|
| Gerätetyp : | Kehrmaschine |
| Working width: | 4m |