Skip to main content Skip to search Skip to main navigation
Menu

Fliegl silage grab bucket »Standard«, 1800 mm, Volume approx. 1.01 m³; Opening width max. 1420 mm (Mounting on Euronorm)

Description

Features

  • Euro-Norm mounting
  • Fully galvanised bucket
  • Cutting edge and grab unit made from HB 500
  • Heavy-duty double-acting hydraulic cylinders
  • Robust grab linkage with additional gusset plates
  • Tapered tines
  • Hydraulic plugs and hoses

Technical data

ManufacturerFLIEGL
Product typeSilage grab bucket
Working width1.800 mm
Capacity1,01 m³
Max. opening width1.420 mm
MountingEuro-Norm
Surface protectionfully galvanised
Cutting edgeHB 500, height 150 mm, thickness 16 mm
Grab unitHB 500
Hydraulic cylindersdouble-acting, heavy-duty design
Unladen weightapprox. 590 kg

Product description

Grab bucket for silage removal

The bucket holds 1,01 m³ and can be fitted to a front loader with a Euro-Norm mounting or to a wheel loader. It is suitable for all types of silage, manure and other bulk materials – and easily fills a feed mixer wagon.

Full galvanisation – no minor detail when handling silage

This is the material choice that determines service life.

Why silage is so aggressive: Lactic acid fermentation produces organic acids – the pH of good silage is between 3,8 and 4,5.

What this means for an attachment:

  • Silage juice is acidic and attacks painted surfaces as soon as the coating is damaged.
  • Damage is inevitable – when cutting into the silage face, contacting the silo wall or setting the attachment down.
  • The attachment stays wet. After removal, silage sticks in the corners and does not dry there.

How galvanising makes a difference: The zinc coating protects the steel even at scratches and cut edges – it provides cathodic protection, including where the coating itself is no longer present.

The difference becomes clear after years: A painted bucket rusts first at the edges and welds. A galvanised one stays intact there – and that is exactly where the load-bearing joints are.

HB 500 in high-wear areas

The cutting edge and grab unit are made from highly wear-resistant steel.

What HB 500 means: A Brinell hardness of around 500 – about three times that of ordinary structural steel.

Why these components in particular:

ComponentLoad
Cutting edgescrapes across concrete floors, picks up material and contacts the silo wall
Grab unitcuts into compacted silage and bears the entire gripping force

The 16 mm thickness of the cutting edge provides additional wear allowance – at 150 mm high, it can be used for a long time before it needs replacing.

Why concrete is harder than you might think: The silo floor is made of concrete with aggregate. Every time silage is removed, the cutting edge scrapes across it – several times a day when feeding daily.

The tapered tines

They do the actual work.

Why the shape matters: Silage at the face is heavily compacted – rolled to 200 to 250 kg of dry matter per cubic metre.

  • Sharp tines penetrate rather than push.
  • Blunt tines push the silage face ahead of them and loosen it.

Why loosening is the real problem: Loose silage draws in air – and air causes secondary heating. The silage spoils at the face before it is fed.

Clean removal is therefore not just a convenience feature, but directly affects feed management.

Removal close to the wall

The manufacturer explicitly lists this as a feature.

Why this matters in practice: In a drive-over silo, the silage is stored between two walls. Silage left against the wall stays there – and spoils.

The consequence: An attachment that cannot reach the wall leaves a strip along both sides. In an 8 m-wide silo, 20 cm on each side amounts to 5% of the feed – a considerable quantity over a season.

The second effect: Silage left against the wall is exposed to air and encourages secondary heating throughout the silage face.

The grab linkage with gusset plates

Additional gusset plates reinforce the grab unit.

Why reinforcement is needed here: The linkage transfers the full force of the hydraulic cylinders to the grab. This is the most heavily loaded point in the structure – and the point where grab buckets typically tear.

What gusset plates do: They distribute the force over a larger area instead of concentrating it at the weld.

The load case that makes this necessary: The grab closes on compacted silage and encounters varying resistance. One side grips while the other slips – the resulting twisting force loads the linkage unevenly.

Double-acting hydraulic cylinders

The cylinders actively operate in both directions.

Why this is essential for a grab: Force is needed to penetrate the silage when closing. It is also needed when opening – tangled grass silage can hold the grab shut, and gravity alone is not enough.

The manufacturer describes them as heavy-duty cylinders – with a width of 1,8 m and compacted silage, considerable closing force is required.

1,01 m³ at a width of 1.800 mm

The figures are matched to one another.

Working width1.800 mm
Capacity1,01 m³
Max. opening width1.420 mm
Unladen weightapprox. 590 kg

Calculating the load for the loader:

  • Grass silage approx. 700 kg/m³ – around 1.300 kg in total when full
  • Maize silage approx. 750 kg/m³ – around 1.350 kg in total when full
  • Manure approx. 800 kg/m³ – around 1.400 kg in total when full

What to check: The rated tipping load of the front loader or wheel loader must be sufficient – at the height at which the load is discharged. When filling a feed mixer wagon, the load is lifted overhead, where stability is at its lowest.

The 1.420 mm opening width

This determines how much can be grabbed in one go.

What this means in practice: The grab can take hold of a block up to 1,42 m high. With a 2 m-high silage face, that is around two layers – meaning only a few grabs per feeding.

Suitable materials

  • Maize silage
  • Grass silage
  • Manure
  • Other bulk materials

The manufacturer also specifies filling feed mixer wagons – controlled discharge is important here to prevent material falling outside the hopper.

The Euro-Norm mounting

The bucket fits front loaders with a Euro-Norm quick-attach system.

What this means: Euro-Norm is the most widely used system for agricultural front loaders. You can switch between a bucket, pallet fork and grab without tools.

For wheel loaders the manufacturer offers mountings by type – the correct mounting depends on the machine.

Applications

Dairy and beef farming, biogas plants, horse keeping and equestrian centres, sheep farming, agricultural contractors, filling feed mixer wagons, manure removal and general bulk-material handling.

Operating notes

  • Check the rated tipping load of the carrier vehicle – depending on the material, the bucket weighs 1.300 to 1.400 kg when full.
  • A double-acting hydraulic connection is required for the grab.
  • Hydraulic hoses and plugs are included – check that the coupling size is suitable.
  • Choose a mounting to suit the carrier vehicle; type-specific mountings are available for wheel loaders.
  • Remove silage cleanly and vertically from the face – loosened silage draws in air and heats up.
  • Work right up to the silo wall; silage left behind will spoil.
  • When filling the feed mixer wagon, ensure the machine is stable and visibility is clear.
  • Do not stand beneath the raised bucket.
  • Close the grab before setting it down; an open grab is a trip hazard.
  • Depressurise the hydraulics before maintenance and secure the attachment against accidental lowering.
  • Check the cutting edge and tines regularly for wear; blunt tines loosen the silage face.
  • Check the grab linkage and pins for play.
  • Remove silage residue after use – silage juice is acidic and can attack galvanised surfaces over time.

Frequently asked questions

How much does the bucket hold?

1,01 m³ at a working width of 1.800 mm. The maximum opening width is 1.420 mm.

Which vehicles does the bucket fit?

Front loaders with a Euro-Norm mounting. Type-specific mountings are available for wheel loaders.

Why is the bucket galvanised?

Silage juice is acidic – the pH of good silage is between 3,8 and 4,5. Galvanising protects the steel even at scratches and cut edges, where paint fails.

What does HB 500 mean?

A Brinell hardness of around 500 – about three times that of ordinary structural steel. The cutting edge and grab unit are made from this material.

How heavy is the bucket when full?

Around 590 kg when empty. Silage adds 700 to 800 kg, depending on the type – around 1.300 to 1.400 kg in total.

Why tapered tines?

Silage at the face is heavily compacted. Sharp tines penetrate rather than pushing the face ahead and loosening it – loose silage draws in air and heats up.

Can I use it to fill a feed mixer wagon?

Yes, the manufacturer explicitly lists this as an application.

What materials can I grab?

All types of silage – maize and grass – as well as manure and other bulk materials.

Properties
Gerätetyp : Silagegeräte
Working width: 1.80m
volume: 1010L