Fliegl silage cutting fork – silage cutting fork, 1850 mm, 16 tines; filling volume 1.6 m³ (Mounting on Euronorm)
€7,100.00
Scope of delivery
- 1 × Fliegl silage shear grab, working width 1.850 mm
- Euronorm mounting bracket (bolted on)
- 16 welded cutting blades/tines
- Powder-coated frame
- Tractor and front loader not included – attachment only
Technical data
| Manufacturer | Fliegl Agrartechnik GmbH, Mühldorf am Inn |
|---|---|
| Product type | Silage shear grab |
| Dealer article number | SSGFLM001850 |
| Working width | 1.850 mm |
|---|---|
| Block height | 1.140 mm |
| Filling volume | 1,6 m³ |
| Number of tines | 16 |
| Tine type | Welded cutting blades |
| Load capacity | ⚠ Not documented – please request from Fliegl |
| Unladen weight (without mounting bracket) | approx. 950 kg (⚠ Approximate figure) |
|---|
| Mounting | Euronorm (bolted on) |
|---|---|
| Drive | Hydraulic |
| Hydraulic connections | 1 double-acting connection |
| Operating pressure | ⚠ Not documented |
| Oil flow rate | ⚠ Not documented |
| Frame | Powder-coated |
|---|---|
| Blades | Welded, painted |
Product description
What a silage shear grab does – and why it is not the same as a silage grab
A silage shear grab is a front-loader attachment that cuts and lifts large blocks from the clamp. The 16 tines penetrate the compacted silage, the welded cutting blades cleanly separate the block, and the front loader lifts it out of the clamp.
The difference compared with a simple silage grab (grab fork): a silage grab spears and grips loose silage – it does not cut it. This is not enough with well-compacted grass or maize silage: the material holds together and cannot be gripped without tearing the face. That is exactly where the silage shear grab performs better – it creates a clean, smooth face, allowing less secondary fermentation.
1.850 mm working width – who it is designed for
The 1.850-mm version is the standard size for medium to larger dairy and cattle farms. It fits common front loaders on medium-sized tractors (from approx. 80–100 PS) and covers the typical removal width in a clamp.
| Working width | Typical use | Suitability |
|---|---|---|
| 1.600 mm | Smaller farms, narrow clamps | More compact front loaders, lighter tractors |
| 1.850 mm | Standard farms, daily feeding | Medium-sized front loaders, 80–120 PS |
| 2.100 mm+ | Large farms, high daily volumes | Heavy-duty front loaders, from 120 PS |
Note: The PS figures are guidelines. Front-loader suitability depends not on engine power, but on the lifting capacity of the front loader and the permissible payload. With an unladen weight of approx. 950 kg plus up to 1,6 m³ of loaded silage, the filled grab can quickly weigh over 1.500 kg – the front loader and tractor must be able to carry this load.
16 tines and a block height of 1.140 mm – what this means in practice
The 16 welded cutting blades are spaced closely enough to cut even short-chopped silage cleanly, without material falling through between the tines. The block height of 1.140 mm limits the maximum block thickness – this is the height of the silage block the grab can lift in one pass.
A typical clamp face advance is 15–30 cm per day (depending on livestock numbers). With a width of 1.850 mm and a height of 1.140 mm, the grab collects enough material in one pass for several feed-out loads – saving trips between the clamp and the feed barrier.
Euronorm mounting – the right connection
The bolted-on Euronorm mounting bracket is the most widely used front-loader connection in Europe. This means the silage shear grab fits front loaders from Stöll, Quicke, Hydrac, MX, Hauer, Weidemann and many others, provided they support Euronorm (ISO 23206).
As the mounting bracket is bolted on, it can be replaced with another mounting bracket if required (e.g. Weidemann, Merlo, Volvo) – provided Fliegl supplies the appropriate adapter plate. Please check before ordering whether your front loader has Euronorm mounting.
Hydraulic drive – one spool valve is enough
The silage shear grab needs just one double-acting hydraulic connection. This is the simplest connection possible – every tractor with a front loader has at least one spool valve. No additional valve or second hydraulic circuit is required.
The hydraulic drive controls the cutting movement of the tines: the tines enter the silage and close like a pair of pincers to cut out the block. The front loader itself provides the lifting movement.
A clean face – why it protects feed quality
When silage is torn out rather than cut, the face becomes loose and ragged. Oxygen enters, secondary fermentation begins, mould develops, and the silage loses energy and palatability. The result: higher feed losses and lower feed intake.
A silage shear grab with sharp, welded blades creates a smooth, compacted face. Less oxygen ingress = less secondary fermentation = better silage quality right down to the last block in the clamp.
What the Fliegl silage shear grab does not have – and why
The grab has no grab top (upper jaw). A grab top over the tines would prevent material falling out upwards during transport, but it would also make the attachment heavier, more expensive and mechanically more complex. With the correct technique – cut the block, lift it briefly, drive straight to the feed barrier – a grab top is not needed for silage.
The attachment has no sideshift. With a silage shear grab that cuts the entire block out of the clamp from the front, moving it sideways is not useful – the grab is positioned using the front loader.
Frequently asked questions
Will the Fliegl silage shear grab fit my front loader?
The grab is supplied with Euronorm mounting (ISO 23206), the most widely used standard in Europe. The lifting capacity of the front loader is also crucial: with an unladen weight of approx. 950 kg plus a loaded silage block, the front loader must be able to safely lift at least 1.800–2.000 kg. Check your front loader’s data sheet.
How much silage will the grab hold?
The filling volume is 1,6 m³. The weight varies depending on the type of silage and how compacted it is: well-compacted maize silage weighs approx. 700–800 kg/m³, and grass silage approx. 500–650 kg/m³. At 1,6 m³, you can therefore transport approx. 800–1.280 kg of silage per load.
How often do the cutting blades need sharpening?
This depends on the type of silage, how compacted it is and how dirty it is. With clean grass silage, the blades will last for several seasons. With maize silage containing more stubble or where sand or soil gets in, their service life is reduced. Blunt blades can be identified by a face that is no longer smooth but ragged. The welded blades can be resharpened or replaced by an agricultural machinery workshop.
Do I need an additional spool valve on the tractor?
No. The silage shear grab needs only one double-acting hydraulic connection, which is standard on every tractor with a front loader. A second spool valve is not required.
Can I also pick up hay or straw with the silage shear grab?
The silage shear grab is designed for compacted silage – material formed into blocks. It is not suitable for picking up loose hay or straw, as these fall through between the tines. For loose bulk material, you need a silage bucket or a grab bucket.
| Gerätetyp : | Silagegeräte |
|---|---|
| Working width: | 1,85m |