Skip to main content Skip to search Skip to main navigation
Menu

Fliegl pallet fork extension, 1800 mm, Length 1800 mm; Internal width 123 mm; Internal height 55 mm; for tine cross-section 120 x 40 mm

Description

Scope of delivery

  • 1 × Fliegl forklift tine extension, 1800 mm

Note: Fork extensions are sold individually (per piece). You need 2 pieces for a set.

Technical data

ManufacturerFliegl Agrartechnik GmbH
Equipment typeForklift tine extension (slip-on)
Extension dimensions
Length1800 mm
Internal width123 mm
Internal height55 mm
Compatible tine cross-section
Tine width120 mm
Tine height40 mm
Tine cross-section120 × 40 mm
Clearance dimensions
Width clearance3 mm (123 mm internal width − 120 mm tine)
Height clearance15 mm (55 mm internal height − 40 mm tine)

Product description

What a fork extension does – and when you need one

A forklift tine extension is a slip-on steel profile that slides over the existing fork tines of a forklift or front loader. The extension increases the tine length without the need to replace the original tines.

Typical applications:

  • Long pallets and special loads: Euro pallets (1200 mm) fit on standard forks. Industrial pallets, pallet cages and long loads (from 1600 mm) do not – this is where the slip-on fork extends the reach.
  • Handling double pallets: Pick up two Euro pallets positioned one behind the other at the same time, without moving them individually.
  • Seasonal use: The extension is fitted only when needed. In normal operation, the forklift works with its standard tines – without extra weight or restricted visibility.

Compatible tine cross-section: 120 × 40 mm

This extension fits fork tines with a cross-section of 120 mm wide × 40 mm high. This is a common size for:

  • Light to medium-duty forklifts (approx. 1.5–2.5 t lifting capacity)
  • Front loader fork carriers with forklift tines
  • Wheel loader pallet forks used in agriculture and municipal applications

Check before purchase: Measure the cross-section of your existing fork tines (width × height). The tine must fit inside the extension's internal profile: 123 mm internal width and 55 mm internal height. Tines wider than 120 mm or higher than 40 mm will not fit. Narrower or lower tines will fit, but will be too loose – the extension will rattle and may slide sideways.

1800 mm length – what this means for residual capacity

The extension is 1800 mm long. The total fork length after fitting is calculated as follows:

Total length = original tine length + (1800 mm − overlap)

The overlap is the section where the original tine sits inside the extension. The extension must not project beyond the original tine by more than 2/3 of its length – this rule of thumb is a guideline under DGUV and FEM regulations. This means:

Maximum projection under the 2/3 rule
Original tine lengthMaximum projectionMinimum overlapWill the 1800 mm extension fit?
800 mm533 mm1267 mmno – tines too short
1000 mm667 mm1133 mmno – tines too short
1200 mm800 mm1000 mmyes – 800 mm projection
1500 mm1000 mm800 mmyes – 1000 mm projection
1800 mm1200 mm600 mmyes – 1200 mm projection

Warning: Every extension reduces the forklift's residual capacity because it moves the load centre forwards. The permissible load decreases in proportion to the increased lever arm. Check your forklift's capacity chart or ask the forklift manufacturer about the residual capacity with extended forks.

Why fork extensions reduce lifting capacity

A forklift is a tipping lever: the front axle is the pivot point, and the weight at the rear acts as a counterweight. The further the load is from the pivot point, the less it can weigh – otherwise the forklift will tip forwards.

Example calculation (simplified):

  • Forklift with a 2,000 kg lifting capacity at a 500 mm load centre distance (standard)
  • Original tines 1200 mm + extension with 800 mm projection = total 2000 mm
  • New load centre distance: approx. 750–800 mm instead of 500 mm
  • Residual capacity: approx. 1,200–1,400 kg instead of 2,000 kg

The exact residual capacity depends on the forklift model. Do not operate at full load without checking the capacity chart.

What the Fliegl fork extension does not have – and when this matters

  • No documented integrated safety device: It is not documented whether the extension is secured to the tine with a locking pin, clamping screw or tensioning latch. Before use, check how the extension is secured against slipping off – an unsecured slip-on profile is a source of accidents.
  • No lifting capacity specified: The extension's maximum load capacity is not specified. In addition to the forklift's residual capacity, the extension itself may further limit the load if its profile is weaker than the original tine.
  • No tip / entry lip: The extension has (in standard construction) an open profile without an angled tip. Inserting it under tightly stacked pallets may be more difficult than with a forged original tine.

Frequently asked questions

Will the extension fit my fork tines?

Measure the cross-section of your existing fork tines: width × height. The extension fits tines measuring 120 mm wide × 40 mm high. The internal profile is 123 × 55 mm, giving 3 mm clearance in width and 15 mm in height. Wider or higher tines will not fit; significantly narrower or lower tines will be too loose.

What is the minimum length of my original tines?

The rule of thumb is that the extension must not project beyond 2/3 of the original tine length. For the 1800 mm extension, this means your original tines should be at least 1200 mm long. With shorter tines, the extension will not fit far enough over them and the risk of tipping increases.

Does the fork extension reduce my forklift's lifting capacity?

Yes, always. The extension moves the load centre forwards, reducing the residual capacity. The extent of the reduction depends on the forklift model and the actual overlap. Check your forklift's capacity chart or ask the forklift manufacturer.

Are the fork extensions supplied in pairs or individually?

The extension is sold as a single item. Order 2 pieces for a complete set.

Can I use the fork extension to lift people?

No. Fork extensions must not be used to transport people. Lifting people with a forklift requires a tested work platform approved under DGUV Regulation 68.

Properties
Gerätetyp : Palettengabel