Fliegl mulcher »BIG« (excavator) – mulcher »BIG«, 800 mm, Mount MS03; 9 flails; 30 l/min
€4,215.00
Scope of delivery
- 1 × Fliegl mulcher, 800 mm, hydraulic, MS03 mount
- 9 flails pre-assembled
- Trailing roller pre-assembled
Technical data
| Manufacturer | Fliegl Agro-Center GmbH |
|---|---|
| Product type | Flail mulcher / excavator mulcher |
| Model | „BIG“ |
| Working width | 800 mm |
| Weight | 295 kg |
| Mount | MS03 |
| Drive | Hydraulic |
|---|---|
| Hydraulic flow rate | 30 l/min (minimum requirement) |
| Max. speed | 3.000 rpm |
| Operating pressure | ⚠ Request from supplier |
| Number of belts | 3 |
| Number of flails | 9 |
|---|---|
| Flail type | Y-flails (bolted) |
| Rotor diameter | ∅ 159 × 8 mm |
| Trailing roller | ∅ 133 × 3 mm |
Product description
Excavator mulcher – why mulch with an excavator?
An excavator mulcher takes mulching to places a tractor cannot reach: embankments, ditch bottoms, the tops of banks, beneath crash barriers, along waterways and across difficult-to-access terrain. The excavator stays on the track and reaches the mulcher over the embankment with its boom – without driving over the ground.
The Fliegl „BIG“ with an 800 mm working width is the most compact version in the BIG range. It is suitable for mini excavators and compact excavators fitted with an MS03 quick coupler and delivering at least 30 l/min hydraulic flow.
9 flails across 800 mm – what does that mean?
Nine Y-flails across an 800 mm working width give a flail spacing of approx. 89 mm. This allows the rotor to process the material very closely – even thin shoots and grass are cleanly chopped, rather than simply bent over.
The Y-flails are bolted on and can be replaced individually. Compared with hammer flails, Y-flails offer:
- Finer mulching results – three cutting edges per flail instead of one striking face
- Lower power requirement – less impact energy, more cutting action
- Longer service life – three usable sides per flail before it needs replacing
MS03 mount – the standard for medium-sized excavators
The MS03 mount is the widely used quick-coupler standard for excavators in the 3–8-tonne class. The mulcher is attached like any other implement using the quick coupler – no tools or manual pinning required.
| Quick coupler | Pin spacing | Typical excavator class |
|---|---|---|
| MS01 | approx. 150 mm | 0,8–2,0 t |
| MS03 (this mulcher) | approx. 250 mm | 3–8 t |
| MS08 | approx. 350 mm | 8–14 t |
Important: The excavator must have an MS03-compatible quick coupler. Alternatively, the mulcher can be adapted to other mounting systems using compatible adapter plates (e.g. Lehnhoff, Verachtert).
30 l/min – is my excavator’s flow rate sufficient?
The mulcher requires a minimum hydraulic flow rate of 30 l/min. This is the flow rate delivered by most compact excavators from around 3 t via an auxiliary control circuit. What happens if the oil flow is too low:
| Flow rate | Effect |
|---|---|
| < 25 l/min | Rotor turns too slowly – poor mulching results and increased wear |
| 30 l/min | Minimum requirement – normal operation |
| 40–50 l/min | Optimal operation – higher speed, better mulching results, faster working |
| > 50 l/min | Consult Fliegl – do not exceed the maximum speed of 3.000 rpm |
Tip: Check your excavator’s manual to see how much flow the auxiliary control circuit (not the travel drive!) delivers. This is usually listed under “Auxiliary hydraulic flow” or “Zusatzhydraulik”.
295 kg – heavy enough for pressure, light enough for the boom
At 295 kg unladen weight, the „BIG“ mulcher is at the heavier end of the range for 800-mm excavator mulchers. This has several advantages:
- More weight pressing down on the surface – the mulcher presses itself into the material, so the excavator operator needs to apply less pressure
- Less vibration – the greater weight dampens vibrations in the boom and dipper arm
- More robust main body – the weight comes from stronger material
At the same time, the excavator must be able to support the 295 kg at the fully extended boom. This is no problem for excavators from around 3,5 t upwards – check stability on smaller machines.
Typical applications
- Embankment maintenance: Roadside, dam and railway embankments – the excavator stays at the top while the mulcher works on the slope
- Ditch maintenance: Keep drainage ditches and roadside ditches clear
- Area mulching: Overgrown areas, fallow land and emerging woody growth up to approx. 20–30 mm stem diameter
- Waterway margins: Bank maintenance and cutting back reed beds – without having to drive over the bank
- Municipal green-space maintenance: Beneath crash barriers, around bridge abutments and on traffic islands
- Solar farms: Vegetation control beneath and between solar panels
Who it is designed for
- Local authorities and road maintenance depots: Embankment maintenance on trunk, regional and local roads
- Water and land management associations: Ditch and bank maintenance
- Landscapers: Clearing areas and maintaining overgrown plots
- Farms with an excavator: Verge maintenance, embankments around silage clamps and farmyard edges
- Agricultural contractors: Embankment mulching as a service using an existing compact excavator
Comparing the BIG range – which working width for which application?
| Feature | 800 mm (this model) | 1000 mm | 1200 mm |
|---|---|---|---|
| Article number | MULBAG000004 | MULBAG000005 | MULBAG000006 |
| Working width | 800 mm | 1.000 mm | 1.200 mm |
| Weight | 295 kg | 320 kg | ⚠ request |
| Mount | MS03 | MS03 | MS03 |
| Hydraulics | 30 l/min | 30 l/min | ⚠ request |
| Ideal application | Narrow embankments, ditches, detailed work | Medium-sized embankments, areas | Large areas, high output |
All three variants have the same MS03 mount and use the same drive concept (belt drive, 3 belts). The wider variants mulch more area per pass, but also require a more powerful excavator to maintain stability with the boom extended.
What the BIG 800 does not have – and why
- No hydraulic motor included: The mulcher is driven by the excavator’s auxiliary control circuit. This saves weight and cost, but requires a powerful excavator.
- No side shift: Unlike large embankment mulchers mounted on an excavator boom, the „BIG“ has no hydraulic side shift. Positioning is done using the excavator’s boom and dipper arm.
- Not designed for forestry mulching: The „BIG“ mulches grass, scrub and thin woody growth up to approx. 20–30 mm. Thicker wood requires a forestry mulcher with higher power and hammer flails.
Frequently asked questions
Which excavators is the mulcher suitable for?
The „BIG“ 800 mm mulcher has an MS03 mount and weighs 295 kg. It is therefore suitable for compact excavators from approx. 3–3,5 t up to around 8 t. The excavator must deliver a hydraulic flow rate of at least 30 l/min via the auxiliary control circuit.
How thick can the branches be that the mulcher cuts?
The „BIG“ is designed for grass, scrub and thin woody growth up to approx. 20–30 mm in diameter. Thicker material requires a forestry mulcher with higher drive power and heavier hammer flails.
How do I replace the flails?
The Y-flails are bolted on. Attach the mulcher, undo the bolts, remove the old flail and bolt on the new one. Allow approx. 10–15 minutes per flail. Always replace the entire set at the same time to minimise rotor imbalance.
Can I also use the mulcher on a larger excavator?
In principle, yes, provided the excavator has an MS03 mount and the speed does not exceed 3.000 rpm. On excavators over 8 t, the flow rate may be too high – in this case, restrict the oil flow at the control valve or choose the larger variant (1000 mm or 1200 mm).
Do I need a low-pressure return line?
Yes, a low-pressure return line (tank return without back pressure) is recommended. Excessive back pressure in the return line increases the temperature of the hydraulic oil and reduces the mulcher’s performance. Check whether your excavator has a separate return connection.
| Gerätetyp : | Mulcher |
|---|---|
| Working width: | 0,80m |