Fliegl heavy material bucket »Standard«, 2600 mm, galvanised; Volume approx. 1.05 m³
€1,665.00
The Fliegl heavy-duty bucket “Standard” with a working width of 2,600 mm is an attachment bucket for wheel loaders and telehandlers – for scraping, scooping and transporting bulk materials. It has a capacity of approx. 1.05 m³, is designed for a load capacity of max. 3,000 kg and weighs only around 330 kg itself.
The body is formed from a single piece, the bottom is reinforced and the top edge is stiffened by a continuous reinforcing profile. The scraping edge is made from highly wear-resistant HB 500 steel. The entire bucket is fully galvanised – corrosion protection that lasts even after years outdoors.
Scope of delivery
- Fliegl heavy-duty bucket “Standard”, working width 2,600 mm, fully galvanised
- Scraping edge made from HB 500, 150 mm wide, 16 mm thick, already fitted
- Reinforced bottom and continuous reinforcing profile along the top edge
- Mounting to suit your loader – configured for you; see below
Not included – please note:
- Quick coupler or adapter plate, if your loader does not already have a compatible mounting system
- Teeth or a tooth bar – the bucket has a smooth scraping edge
- Hold-down, grab attachment or other additional equipment
- Transport to the place of use. At 2,600 mm wide and around 330 kg, the bucket cannot be sent as a parcel – see below for details.
Important: the mounting is configured for you
This is the key point with this item, and we would rather tell you beforehand than afterwards: the bucket is not supplied as a standard off-the-shelf product. The mounting – the part that connects the bucket to your loader – is made to suit your machine. That is why we will contact you after you place your order, before anything is built.
What you should have ready:
- Manufacturer and model designation of your loader – ideally read from the identification plate, rather than relying on memory
- The mounting system already fitted, if you know it (e.g. a standardised quick coupler or a manufacturer-specific mounting)
- Two or three photos of the existing mounting: one from the front, one from the side and one with an attachment fitted
- If available: dimensions of the mounting plate on your existing attachment
This information will allow us to identify the mounting precisely. If you are unsure, simply send us the photos and we will tell you what you have.
The range is available in six working widths
This version is the 2,600 mm variant. The galvanised “Standard” heavy-duty bucket is available with a wheel loader or telehandler mounting in the following widths:
- 1,800 mm
- 2,000 mm
- 2,200 mm
- 2,400 mm
- 2,600 mm – this version
- 2,800 mm
The width should be chosen to suit your loader, not the volume you want: a bucket that is noticeably wider than the machine clears the ground cleanly, while one that is too wide for the machine makes it unstable as it enters the pile and puts an uneven load on the front axle. If you are unsure, tell us the manufacturer and model of your loader; we will advise which width suits your machine and give you the capacity and weight of the relevant version.
Working width of 2,600 mm: what it offers
For a bucket, width is the most important performance figure, not volume. At 2,600 mm, it is wider than many wheel loaders and telehandlers – and that makes a difference to the work in two ways:
- A clean surface in one pass. As the bucket extends beyond the tyre tracks, no strip is left behind when scraping and pushing material together that you then have to clear on the next pass. In a shed, on a silage clamp or at a pile, this is the biggest time-saver.
- Higher throughput with light materials. With wood chips, grain or compost, volume rather than weight is the limiting factor. A wide bucket fills in one pass.
The width also has a downside – when transporting it on public roads and passing through narrow entrances. We cover this further down, as it is something to check before buying.
What 1.05 m³ and 3,000 kg mean in practice
These two figures need to be considered together; on their own, they tell you little. A level-full bucket with a capacity of 1.05 m³ will weigh very different amounts depending on the bulk material. The following figures are rough guidelines – moisture and compaction can change them considerably:
| Material | Approx. bulk density | Approx. contents | With bucket at the mounting |
|---|---|---|---|
| Wood chips | 0.25–0.35 t/m³ | 260–370 kg | 590–700 kg |
| Grain | 0.70–0.80 t/m³ | 740–840 kg | 1,070–1,170 kg |
| Compost, manure | 0.70–0.90 t/m³ | 740–950 kg | 1,070–1,280 kg |
| Soil, wet | 1.50–1.70 t/m³ | 1,580–1,790 kg | 1,910–2,120 kg |
| Sand, wet | 1.60–1.80 t/m³ | 1,680–1,890 kg | 2,010–2,220 kg |
| Gravel, crushed stone | 1.70–1.90 t/m³ | 1,790–2,000 kg | 2,120–2,330 kg |
| Building rubble, wet | 1.90–2.20 t/m³ | 2,000–2,310 kg | 2,330–2,640 kg |
This leads to a useful point when deciding whether to buy: even with the heaviest commonly handled material, a level-full bucket remains below the 3,000 kg load capacity. In everyday use, the limiting factor is therefore not the bucket but your loader.
So check your machine’s data sheet for its payload and tipping load at full reach – and add the bucket’s own weight of around 330 kg. With a telehandler, the permitted load also drops considerably when the boom is extended; the load chart, not the maximum figure, is what matters. If you tell us the manufacturer and model, we can work it out together.
Why “formed from a single piece” matters
The bucket body is formed from a single piece, rather than assembled from several sheets. This may sound like a minor detail, but it affects the point where buckets typically fail: the transition from the bottom to the back wall. This is where the greatest force is applied as the bucket enters a pile. A weld at this point is a weak spot; a continuous formed radius has no such joint.
There are two further reinforcements designed to withstand the same stresses:
- Reinforced bottom – where the bucket scrapes over concrete, crushed stone and tarmac
- Continuous reinforcing profile along the top edge – this keeps the bucket in shape when it enters a pile at an angle. This is exactly when twisting occurs, and a twisted bucket will never sit flush on the ground again.
The tapered design works in the same way, but when unloading: as the bucket narrows towards the back, the bulk material slides out more easily instead of sticking in the corners. With wet soil, manure and cohesive materials, this is the difference between tipping out and having to knock the material loose.
HB 500 scraping edge: what the specification means
HB 500 is a Brinell hardness rating – it denotes wear-resistant steel, which is considerably harder than ordinary structural steel. This is exactly where it is needed: the scraping edge is the part that drags along the ground and takes virtually all the wear on the bucket.
The edge is 150 mm wide and 16 mm thick – enough material to wear down before any load-bearing part is reached. Two practical points:
- On concrete and tarmac, any scraping edge wears faster than on natural ground. If you scrape the silage clamp every day, keep an eye on the condition of the edge.
- The galvanising protects the bucket body. Any coating on the scraping edge itself wears off during use – this is normal and not a defect.
If you would like to know whether and how the edge can be replaced later, ask us before ordering and we will check for you.
Fully galvanised: the difference after three years
A bucket spends most of its time outdoors, often with traces of wet soil, salt or manure inside. On a painted bucket, rust starts at the first stone chip and spreads beneath the paint. Fully galvanised means the zinc coating covers the entire component, inside and out, including corners and cavities that a paintbrush could never reach.
For an attachment expected to last 10 or 15 years, this is the factor that makes the biggest difference in value – and it only becomes apparent years later, when you come to sell it.
Check before buying: width, transport and road use
Two points we would rather mention now:
- At 2,600 mm, it is wider than the generally permitted vehicle width of 2.55 m. Whether you can drive on public roads with the bucket attached depends on your vehicle and how you use it – agricultural and forestry implements are subject to different limits in some cases than commercial vehicles. If in doubt, check with your vehicle registration authority before ordering. Width is not an issue on your own premises.
- Measure narrow entrances. Shed doors, barn entrances and silage clamp entrances: allow for 2.60 m plus room to manoeuvre. This is easily overlooked because the bucket is wider than the loader.
Delivery is by haulage company. At around 330 kg and 2.60 m wide, you will need a forklift, front loader or crane to unload it.
Technical data
| Equipment type | Attachment bucket for wheel loaders and telehandlers |
|---|---|
| Working width | 2,600 mm |
| Depth | 860 mm |
| Height | 740 mm |
| Capacity | approx. 1.05 m³ |
| Load capacity | max. 3,000 kg |
| Own weight | approx. 330 kg |
| Scraping edge | Highly wear-resistant HB 500 steel, 150 mm wide, 16 mm thick |
| Design | Tapered, formed from a single piece |
| Reinforcements | Reinforced bottom; continuous reinforcing profile along the top edge |
| Surface | Fully galvanised |
| Mounting | For wheel loaders or telehandlers, configured to customer requirements |
| Application | Scraping, scooping and transporting bulk materials |
The overall width and weight with the mounting fitted depend on the version selected. We will confirm both once the mounting has been specified.
Frequently asked questions
Will the bucket fit my loader?
We will confirm this with you before manufacture: the mounting is configured to suit your machine, so we will contact you after you place your order. Please have the manufacturer and model designation of your wheel loader or telehandler ready – ideally from the identification plate – and, if possible, two or three photos of the existing mounting. If you do not know which system you have, just send us photos and we will identify it.
How much can I lift with the bucket?
The bucket is designed for max. 3,000 kg. In practice, this is rarely the limiting factor: a level-full bucket weighs around 1,800 to 2,000 kg with wet sand or crushed stone, and considerably less with grain or wood chips. The payload of your loader is what matters – and this must include the bucket’s own weight of around 330 kg. The load chart also applies to telehandlers: the permitted load drops considerably when the boom is extended.
What does HB 500 mean for the scraping edge?
HB 500 is a Brinell hardness rating and denotes wear-resistant steel, which is considerably harder than ordinary structural steel. The scraping edge is the part that drags along the ground and takes virtually all the wear – here it is 150 mm wide and 16 mm thick. It wears faster on concrete and tarmac than on natural ground.
Why is the bucket galvanised rather than painted?
Because a bucket is left outdoors, with traces of wet soil, manure or salt inside. With paint, rust starts at the first stone chip and spreads underneath. Fully galvanised means the zinc coating covers the entire component – inside, outside and in the corners. Any coating on the scraping edge itself wears off during use; this is normal.
Can I use it on the road at 2,600 mm wide?
This needs to be checked for your vehicle. At 2,600 mm, it exceeds the generally permitted vehicle width of 2.55 m; agricultural and forestry implements are subject to different limits in some cases than commercial vehicles. If in doubt, check with your vehicle registration authority beforehand. Width is not an issue on your own premises – there, it is an advantage.
What is the bucket suitable for – and what is it not suitable for?
It is designed for scraping, scooping and transporting bulk materials: soil, sand, gravel, crushed stone, building rubble, grain, wood chips, compost and manure. The tapered shape helps the material slide out. It is not designed for breaking or levering – so not for ripping rock, lifting loads by the scraping edge or replacing a ripper tooth. This can twist any bucket, and a twisted bucket will never sit flush on the ground again.
| Gerätetyp : | Schaufel |
|---|---|
| Working width: | 2.60m |
| volume: | 1050L |