Skip to main content Skip to search Skip to main navigation
Menu

Fliegl forklift adapter »Multi-Hitch«, implement side three-point mount Cat. 2; inner fork pockets 148 x 70 mm; ball-head coupling K80; load hook up to 2.5 t

Description

Scope of delivery

  • 1 × Fliegl forklift adapter „Multi-Hitch“, implement-side three-point linkage Cat. II, galvanised

Technical data

ManufacturerFliegl Agro-Center GmbH
Product typeForklift adapter / manoeuvring adapter
Model„Multi-Hitch“
Surface finishGalvanised
Weight125 kg
Mounting and couplings
Forklift pockets (internal)148 × 70 mm
Implement-side mountingThree-point linkage Cat. II
Ball hitchK80
Drawbar eye pin∅ 35 mm
Load hookup to 2.5 t

Product description

Four functions in one adapter

The Fliegl Multi-Hitch turns any forklift into a mobile manoeuvring and coupling station. It is picked up and secured using the forklift forks, and offers four connection options at the rear:

Connection options at a glance
ConnectionSpecificationTypical use
Three-point linkage Cat. IICat. II top and lower link pinsManoeuvre and move three-point linkage implements, and hitch them to a tractor
K80 ball hitch80 mm ball diameter to ISO 24347Manoeuvre trailers with a K80 towing eye
Drawbar eye pin∅ 35 mmConnect and manoeuvre trailers with a ∅ 35 mm drawbar eye
Load hookup to 2.5 tAttach loads, towing work and recovery operations around the premises

Why use it on a forklift rather than a tractor?

On many farms, the forklift is closer to the shed than the tractor. Trailers, implements and wagons need to be manoeuvred regularly – from the storage area to the workshop, from the shed to the yard, or from the parking area to the loading ramp. Starting the tractor every time is a waste of time. The Multi-Hitch turns the forklift into a manoeuvring vehicle:

  • Drive the forklift up – insert the forks into the pockets and secure them
  • Hitch up the trailer or implement – K80, drawbar eye or three-point linkage
  • Manoeuvre – short distances on hard surfaces
  • Park and unhitch – the forklift can carry on

Forklift pockets 148 × 70 mm – will they fit my forklift?

The forklift pockets with internal dimensions of 148 × 70 mm accommodate standard forklift forks. Common fork sizes:

Common forklift fork cross-sections
Fork cross-section (W × H)Typical forkliftsFits?
100 × 40 mmSmall electric forklifts, 1–1.5 tYes
120 × 45 mmStandard forklifts, 1.5–2.5 tYes
125 × 50 mmStandard forklifts, 2–3 tYes
140 × 50 mmForklifts, 2.5–3.5 tYes (tight fit)
150 × 60 mmHeavy forklifts, 3.5–5 tNo – fork width exceeds 148 mm

Important: Measure the fork cross-section (width × height) before ordering. The pockets have an internal width of 148 mm and an internal height of 70 mm – the forks must be smaller than these dimensions.

K80 ball hitch – the standard for heavy trailers

The K80 hitch (80 mm ball diameter) is the standard for agricultural trailers and implements in Europe. It transfers vertical loads of up to 3 t and towing loads of over 20 t, depending on the hitch design. On a forklift, it is typically used for manoeuvring around the premises – not for road transport.

Load hook up to 2.5 t – what does this mean?

The load hook on the Multi-Hitch is designed for a towing force of up to 2.5 t. Typical applications:

  • Moving heavy trailers or wagons around the yard
  • Pulling bogged-down machinery free on the premises
  • Towing loads over short distances on hard surfaces

Note: The load hook is intended for manoeuvring and towing work around the premises, not for lifting loads as a crane hook.

Galvanised – long-lasting protection

The entire adapter is galvanised. This is the right surface protection for equipment that is constantly used outdoors and regularly subjected to mechanical stress – no need to repaint after scratches, with cathodic protection at damaged areas.

Cat. II vs Cat. III – which version do I need?

Multi-Hitch version comparison
FeatureCat. II (this version)Cat. III
Article numberSWRFLM000003SWRFLM000006
Three-point linkage categoryCat. IICat. III
Lower link pin diameter28.6 mm36.5 mm
Top link pin diameter25.4 mm32 mm
Typical tractor size30–100 hp80–250+ hp
Typical implementsLight to medium implementsHeavy implements

The category determines the pin diameter of the three-point linkage mounting. Implements with a Cat. II three-point linkage do not fit a Cat. III adapter, and vice versa, unless reducing bushes are used.

Who it is designed for

  • Farms: Manoeuvre trailers and implements around the yard without starting the tractor
  • Agricultural merchants and machinery dealers: Move new and demonstration machinery around the site using a forklift
  • Local authorities and railway depots: Move trailers between sheds and loading ramps
  • Agricultural contractors: Reposition machinery in a confined space – faster than using a tractor
  • Workshops and repair businesses: Pull implements into the workshop for repair

What the Multi-Hitch is not – and why

  • Not a road vehicle: The adapter is intended for manoeuvring work around the premises. A forklift with a trailer hitched to it must not be driven on public roads.
  • Not a crane hook: The load hook is designed for horizontal towing forces, not vertical lifting loads.
  • No Piton-Fix mounting: Three-point linkage Cat. II only (or Cat. III in the other version). A separate adapter is required for Piton-Fix implements.

Frequently asked questions

Can I tow a trailer on the road with the Multi-Hitch?

No. The Multi-Hitch is intended for manoeuvring work around the premises. A forklift is not an approved towing vehicle for use on public roads.

Which forklift forks fit in the pockets?

The forklift pockets have internal dimensions of 148 × 70 mm (width × height). Standard forks with a cross-section of up to approx. 140 × 65 mm will fit. Forks on heavier forklifts (with a capacity of approx. 3.5 t or more) may be too wide – measure them first.

What is a K80 ball hitch?

The K80 hitch is the European standard for agricultural trailer couplings. The ball has a diameter of 80 mm (to ISO 24347). The trailer's towing eye closes around the ball and locks automatically.

Do I need the Cat. II or Cat. III version?

It depends on the implements you want to manoeuvre. Implements for tractors up to approx. 100 hp are generally Cat. II. Implements for tractors over 100 hp are often Cat. III. Check the pin diameter on your implements: 28.6 mm = Cat. II, 36.5 mm = Cat. III.

How much can I tow using the load hook?

The load hook is designed for a towing force of up to 2.5 t. The actual towing capacity depends on the forklift's tractive force and weight – light forklifts can lose traction under heavy loads.

Properties
Gerätetyp : Adapter / Aufnahme