Fliegl electric universal spreader »Fliegl«, 12 V motor 170 W; spreading width 2–24 m; hopper 90 l
€1,045.00
Standard equipment
- Powder-coated frame
- Plastic hopper with a capacity of 90 l
- Hopper lid
- Electrically driven spreading disc with adjustable vanes
- Agitator for grass seed
- Control panel for operation while driving
- 3 m power cable
- 6 m implement cable
Not included: three-point linkage mount and deflector plates.
Technical data
| Manufacturer | FLIEGL |
|---|---|
| Product type | Electric universal spreader |
| Hopper capacity | 90 l |
| Hopper material | Plastic |
| Drive | 12 V motor, 170 W |
| Speed | 2,600 rpm |
| Torque | 0.4 Nm |
| Spreading width | 2 – 24 m, infinitely variable |
| Dimensions (W × H × D) | 520 × 600 × 900 mm |
| Power cable | 3 m |
| Implement cable | 6 m |
| Control functions | Spreading disc speed, discs on/off, slide gate open/closed |
| Vanes | adjustable |
Important note: The spreader is not suitable for winter maintenance or for spreading salt or de-icing agents.
Product description
90-litre electric universal spreader
The spreader has an integrated 12-volt drive. This means it operates without other drive units such as a PTO shaft or hydraulics – saving time and money.
The 12-volt drive – that’s the key point
Power is supplied by the vehicle’s electrical system.
| PTO drive | Hydraulic drive | 12-volt drive | |
|---|---|---|---|
| Vehicle requirement | PTO | Auxiliary circuit | 12 V socket |
| Attachment | Connect the PTO shaft | Connect the hoses | Plug in the connector |
| Carrier vehicles | Tractor | Tractor, loader | Almost any vehicle |
What this means in practice: The spreader works with tractors, quad bikes, off-road vehicles, pick-ups, yard loaders and compact tractors – anywhere there is a 12 V power supply.
The second advantage: No wear on the PTO shaft or hydraulic couplings, no leaks and no oil loss.
With a power consumption of 170 W the current draw is around 14 A – easily supplied by any vehicle electrical system.
Operated from the cab via the control panel
Three functions can be controlled while driving.
- Increase/decrease spreading disc speed – adjusts the spreading width
- Spreading discs on/off – switch off at the end of the field
- Slide gate open/closed – adjusts the application rate
Why this determines application quality: The two parameters, speed and slide gate position, are independent of each other. Speed determines how far the material is thrown; the slide gate determines how much is dispensed.
What this makes possible: At the field edge, reduce the speed so nothing is thrown into the ditch – the amount per square metre remains the same, controlled by the slide gate.
Switching off at the headland also prevents a double application there.
Spreading width of 2 to 24 m – a wide range
The width is adjusted continuously via the spreading disc speed.
| Width | Typical application |
|---|---|
| 2 – 6 m | Tracks, headlands, slug pellets at field edges, small areas |
| 8 – 14 m | Grassland overseeding, cover crops |
| 18 – 24 m | Wide-area application of lightweight spreading material |
What actually determines the achievable width: not just the speed, but also the spreading material. Heavy, round granules travel considerably further than lightweight seed – 24 m is the maximum under favourable conditions.
Therefore: The actual working width should be checked for each spreading material – ideally by checking the spread pattern using trays.
Adjustable vanes
The vanes on the spreading disc can be adjusted.
What they do: The angle of the vane determines the direction in which the material leaves the disc.
- Set symmetrically – even distribution to both sides.
- Adjusted to one side – boundary spreading at the field edge, to prevent material reaching watercourses, hedges or neighbouring areas.
Why this may be legally relevant: Fertilisers are subject to buffer-zone requirements near watercourses. A spreader that cannot limit spreading to one side can only be used there to a limited extent.
The agitator for grass seed
A small detail with a big impact.
The problem with grass seed: Grass seed is lightweight, fibrous and prone to bridging. It can hang up in the hopper, stopping the flow from the outlet – even when the hopper is full.
What the agitator does: It keeps the material moving and prevents it from forming a bridge over the outlet.
Why this matters with this spreader: Grassland overseeding is one of its main applications. Without an agitator, this very application would be problematic.
What the spreader is designed for
- Cover crops
- Fertiliser and rubber granules
- Grassland overseeding
- Slug pellets
- Silage additives
What these applications have in common: moderate quantities per hectare and free-flowing spreading material. A 90-litre hopper is too small for high fertiliser application rates on large fields – an attachment spreader with PTO drive is the right choice there.
Not for winter maintenance or salt – why this is stated so clearly
The manufacturer expressly rules this out.
The reasons lie in the design:
- Salt is extremely corrosive. Road salt attracts moisture and forms a concentrated solution that attacks metal parts, the motor and the electrical system.
- The hopper is not designed for this. Salt spreaders have stainless steel hoppers and suitably protected drives.
- The electrical components are exposed. A 12 V drive with control cables in salt spray will have a short service life.
- The metering is unsuitable. Road salt flows differently from seed and granules.
What happens if this advice is ignored: The spreader will corrode within one season. And damage caused by improper use is not covered by the warranty.
For winter maintenance stainless steel hopper spreaders are the right choice – such as professional spreaders with a spreading disc and PTO drive.
Cable lengths
| Power cable | 3 m – from the battery to the control panel |
|---|---|
| Implement cable | 6 m – from the control panel to the spreader |
Why this arrangement makes sense: The 3 m cable reaches from the battery to the cab, and the 6 m cable from the cab to the rear-mounted implement – even on larger tractors.
Please note: The cables may be too short on very large vehicles or for front mounting. Measure the cable route before ordering.
What is not included
Two points to clarify before ordering.
| Component | Purpose |
|---|---|
| Three-point linkage mount | Attaching to the carrier vehicle |
| Deflector plates | Limiting and directing the spread pattern |
Why this matters: The spreader cannot be mounted without a mount. The correct mount depends on the carrier vehicle – three-point linkage, rear carrier, load bed or quad bike bracket.
The deflector plates direct the spread pattern precisely – for example, for boundary spreading or where material must not be deflected to the side. They are not essential for most applications across open areas, but are useful near field edges.
Hopper capacity – a calculation
| Application | Quantity per ha | Area per fill |
|---|---|---|
| Grassland overseeding | approx. 20 – 30 kg | around 2 to 3 ha |
| Cover crop | approx. 20 – 40 kg | around 1.5 to 3 ha |
| Slug pellets | approx. 3 – 7 kg | considerably more |
These figures are indicative – the actual fill weight depends on the bulk density of the spreading material. 90 litres of grass seed weighs considerably less than 90 litres of fertiliser granules.
What this means: The capacity is suitable for smaller areas, headlands and overseeding. Frequent refilling becomes a time factor on large fields.
Applications
Grassland farming and overseeding, cover crop cultivation, slug control, silage making, part-time farms, contractors working on smaller areas, equestrian facilities and horse paddocks, local authorities and grounds maintenance, game cover and hunting areas.
Operating notes
- Order the three-point linkage mount to suit the carrier vehicle separately – it is not included.
- Do not use with road salt or de-icing agents – the spreader is not designed for this; damage is not covered by the warranty.
- Provide a suitably fused 12 V supply; the current draw is around 14 A.
- Route the cables so they cannot be crushed or chafed.
- Check the spread pattern before use – the actual working width depends greatly on the spreading material.
- Set and calibrate the application rate using the slide gate position and forward speed.
- Adjust the vanes accordingly when boundary spreading.
- Observe buffer-zone requirements near watercourses and field boundaries when applying fertilisers.
- Observe approval and application requirements when using slug pellets and plant protection products.
- Keep the hopper lid closed in wet weather; damp spreading material will clump.
- Empty and clean the hopper after every use – fertiliser residues attract moisture and corrode components.
- Check the spreading disc and outlet for residue.
- Do not enter the spreading area.
- Store in a dry, frost-free place.
Frequently asked questions
Do I need a PTO or hydraulics?
No. The integrated 12-volt drive operates without other drive units – a 12 V supply on the vehicle is all that is needed.
Can I use it for winter maintenance?
No. The spreader is expressly not suitable for winter maintenance or for salt or de-icing agents. Salt attacks the hopper, drive and electrical system.
Is the three-point linkage mount included?
No, the three-point linkage mount and deflector plates are not included. The correct mount depends on the carrier vehicle.
How wide does the spreader spread?
2 to 24 m, continuously adjustable via the spreading disc speed. The actual width depends on the spreading material – heavy granules travel further than lightweight seed.
What can I spread?
Cover crops, fertiliser and rubber granules, grassland overseeding, slug pellets and silage additives.
How is the spreader operated?
Via a control panel while driving: increase/decrease spreading disc speed, spreading discs on/off and slide gate open/closed.
What is the agitator for grass seed for?
Grass seed is lightweight and fibrous, and tends to bridge in the hopper. The agitator keeps the material moving so that it flows evenly to the outlet.
What is the hopper capacity?
90 litres. For grassland overseeding, this is enough for around two to three hectares, depending on the seeding rate and bulk density.
| Gerätetyp : | Streuer |
|---|