Skip to main content Skip to search Skip to main navigation
Menu

Fliegl concrete mixing bucket (excavator) – concrete mixing bucket, Mount MS10; W x H x D 1950 x 1050 x 105 mm; Oil pressure max. 190 bar; Chain drive; Nominal capacity 590 l

Description

Equipment

  • MS10 mount for excavator attachment
  • Hydraulic discharge opening
  • Hydraulic grid opening
  • Standard changeover valve – only 1 double-acting connection required
  • Inner mixing auger made from wear-resistant HB 450
  • Robust chain drive with heavy-duty OMT hydraulic motor
  • Robust bearing arrangement with special sealing
  • Dual pressure relief valve

Technical data

ManufacturerFLIEGL
Product typeHydraulically driven concrete mixing bucket for excavators
MountMS10 quick coupler
Rated capacityapprox. 500 l
Max. capacityapprox. 590 l
Heightapprox. 1.050 mm
Widthapprox. 1.950 mm
Unladen weightapprox. 770 kg
Recommended oil flow70 l/min
Max. oil flow150 l/min
Normal oil pressure160 bar
Maximum oil pressure190 bar
Connections required1 × double-acting
DriveChain drive via OMT hydraulic motor
Mixing auger materialHB 450
Pressure reliefdual, standard

Product description

Concrete mixing bucket for excavators

The bucket mixes concrete directly on site and dispenses it in controlled quantities through a hydraulic discharge opening. The MS10 mount connects it to the excavator quick coupler, and it is driven by a chain drive with a heavy-duty hydraulic motor.

On an excavator rather than a loader – what changes

That is the key difference compared with the loader version.

On a wheel loaderOn an excavator
Reachlimited to vehicle widthvia the boom
Discharging into trenchesdifficultdirectly possible
Working over obstaclesnoyes
Slewing on the spotno360°
Filling from a stockpileeasypossible using the boom

Why this makes all the difference in practice: Concrete needs to be delivered where the formwork is – and that is often somewhere no vehicle can reach.

  • Foundations in trenches – the excavator stays at the top and discharges downwards.
  • Behind obstacles – over walls, fences and embankments.
  • A series of pad foundations – the excavator slews from hole to hole without moving.
  • Confined sites – where a wheel loader cannot manoeuvre.

The time saving is considerable: Instead of transporting concrete from the loader to the formwork by wheelbarrow and shovel, it is delivered directly from the mixing bucket.

The MS10 mount

MS10 is a quick-coupler system for excavators.

What this means: Switching between the bucket and mixing bucket is done using the existing quick coupler – no pins, no tools.

Checks to make before ordering:

  • Which quick-coupler system is fitted to the excavator. MS10 is not compatible with other systems – adapters are not available for every combination.
  • Whether the quick coupler is rated for the weight. When full, the bucket weighs around 1.970 kg.
  • Whether an auxiliary circuit is available – to drive the mixing auger.

One double-acting connection for both functions

The standard changeover valve means that only one double-acting connection is required – for the slide and grid together.

Why this is particularly important on an excavator: Excavator booms have a limited number of hydraulic lines. After the quick-coupler circuit and auger drive, there is often only one circuit left – and that is exactly what the changeover valve is designed for.

The second benefit: Fewer lines on the boom mean fewer points of abrasion and fewer couplings to operate when changing attachments.

The hydraulic grid opening

The grid sits over the bucket opening.

  • When filling it keeps out stones, lumps and foreign objects.
  • When mixing it prevents splashing.
  • As a guard against reaching into the moving auger.

Why hydraulic: The bucket hangs out of reach on the excavator boom. A manually opened grid would only be accessible when the attachment is set down – every time it is filled.

HB 450 mixing auger

A Brinell hardness of around 450 – about two and a half times that of ordinary structural steel.

Why wear-resistant steel is needed here: Fresh concrete is one of the most abrasive materials there is. Sand and chippings act like abrasives, while the auger moves constantly through the mix.

What happens with softer steel: The auger flights become thinner and shorter. The gap to the drum wall increases – material is left behind and the mixing quality deteriorates.

Chain drive with OMT hydraulic motor

  • Torque conversion. The chain provides a low speed with high torque.
  • Shock absorption. If a stone briefly blocks the auger, the drive train absorbs the shock.
  • Repairable. The chain and sprocket are replaceable wear parts – unlike a damaged gearbox.

The OMT is a heavy-duty series orbital motor, designed for high torque at low speeds.

Robust bearing arrangement with special sealing

This is where mixing buckets typically fail.

The problem: The auger shaft passes through the drum wall and must be sealed against fresh concrete while moving.

What happens if the seal is inadequate: Cement slurry gets into the bearing, sets and destroys it. The damage only becomes apparent once the shaft develops play.

Dual pressure relief valve

It protects the drive from overloading in both directions of rotation.

Against what: If a stone, piece of reinforcement or set concrete blocks the auger, the pressure rises sharply.

Why dual: Protection is just as necessary when reversing to free a blocked auger as it is during normal operation.

Hydraulic requirements

ValueSpecification
Recommended oil flow70 l/min
Maximum oil flow150 l/min
Normal oil pressure160 bar
Maximum oil pressure190 bar

The critical figure is 70 l/min. Below this, the auger turns too slowly – mixing takes longer and, with stiff concrete, the material may stop moving.

Additional points to consider on an excavator: The auxiliary circuit must be able to deliver the flow continuously, not just at peak output. The return line must also be adequately sized – back pressure in the return line can damage the hydraulic motor.

Calculating the weight – particularly important on an excavator

Unladen weightapprox. 770 kg
500 l fresh concrete (approx. 2.400 kg/m³)around 1.200 kg
Total weight when fullaround 1.970 kg

At the maximum capacity of 590 litres the total weight rises to around 2.190 kg.

Why this is more critical on an excavator than on a loader: An excavator's lifting capacity depends on its reach. A load that can be lifted easily close to the machine may pose a tipping risk at full reach – and that is exactly where the bucket is discharged.

The excavator's load chart is decisive, not its operating weight class. Check the load at the actual reach and height at which the work will be carried out.

Mixing on site – when it pays off

Ready-mixed concreteMixing bucket
Minimum orderusually several m³none
Deliverychargednot required
Waiting timedelivery slotavailable immediately
Accessibilitymixer must be able to reach the siteexcavator reaches the spot
Mix designspecifiedfreely selectable

This is doubly true for excavator work: Anyone working in a trench already has the machine there. The mixing bucket also turns the excavator into a concrete plant – without a second vehicle or repositioning.

Typical applications: Foundations for fence posts and masts, backfilling service trenches, concrete work around manholes, pad foundations for carports and patios, repairs to bank protection.

The hydraulic discharge opening

The slide can be opened continuously.

This is particularly useful on an excavator: Concrete flows in a controlled manner into narrow formwork or a post hole – the excavator holds the bucket in position above it while the concrete is dispensed in measured quantities.

The second benefit: Any remaining concrete stays in the drum and can be used at the next location.

Applications

Civil engineering and utility construction, landscaping, fence and post installation, construction companies, farms, local authorities and depots, bank protection and water management, equipment hire.

Operating instructions

  • Check the excavator's quick-coupler system – the mount is designed for MS10.
  • Check the lifting capacity at the actual reach – the bucket weighs around 1.970 kg when full, or around 2.190 kg at maximum capacity.
  • Check the hydraulics: recommended 70 l/min, maximum 150 l/min at 160 to 190 bar.
  • One double-acting connection is sufficient for the slide and grid; the auger drive is additional.
  • Ensure the return line is adequately sized.
  • After coupling, check that the quick coupler is fully locked.
  • When discharging, stand on level, firm ground and ensure the machine is stable.
  • Never reach into the moving auger – not even to remove foreign objects.
  • Never stand beneath the raised bucket.
  • Keep the grid closed while mixing.
  • Before working on the attachment, depressurise the hydraulics and secure the machine against accidental start-up.
  • Rinse thoroughly with water after every use – set concrete blocks the auger and is very difficult to remove.
  • Regularly check the bearing and seal for leaks.
  • Check the chain for tension and wear, and lubricate it in accordance with the manufacturer's instructions.
  • In freezing conditions, empty the bucket and store it dry.

Frequently asked questions

Will the bucket fit my excavator?

The mount is designed for an MS10 quick coupler. Check the existing system on the excavator before ordering – MS10 is not compatible with other systems.

How many hydraulic connections do I need?

One double-acting connection for the slide and grid, made possible by the standard changeover valve. The mixing auger drive is additional.

How much oil does the bucket need?

Recommended 70 l/min, maximum 150 l/min at 160 bar normal pressure and 190 bar maximum pressure. Below 70 l/min, the auger turns too slowly.

How heavy is the bucket when full?

Around 770 kg empty. 500 litres of fresh concrete adds approximately 1.200 kg, giving a total of around 1.970 kg. The excavator's lifting capacity at the actual reach is decisive, not its operating weight class.

What is the advantage over the loader version?

Reach. The excavator can discharge into trenches, over obstacles and slew from one pad foundation to the next without moving.

What does HB 450 mean for the mixing auger?

A Brinell hardness of around 450 – about two and a half times that of ordinary structural steel. Sand and chippings in fresh concrete act like abrasives on the auger.

What is the dual pressure relief valve for?

It protects the drive if the auger becomes blocked, in both directions of rotation. This protection is also needed when reversing to free it.

When is a mixing bucket worthwhile compared with ready-mixed concrete?

For small quantities, dispersed work sites and sites with poor access. If you are already working in a trench with an excavator, you do not need a second vehicle.

Properties
Gerätetyp : Mischer
volume: 590L