Fliegl concrete mixer »Garant« – concrete mixer »Garant 401 SS«, Volume 400 l; Output approx. 7 m³/h; Power requirement min. 40 hp; Filling diameter 1100 mm; Three-point mount Cat. 2; 2-speed gearbox 1:11
€3,250.00
Features
- Category 2 three-point linkage, adjustable to three positions
- Forklift pockets, internal lug dimensions 190 × 60 mm
- 2-speed gearbox, ratio 11:1
- PTO shaft with overload protection
- Hopper and mixing tools made from highly wear-resistant steel
- Hopper base reinforced in a star pattern
- Mixer shaft supported at three points, with bearings protected against dirt
- Mixing tools adjustable sideways and downwards on 3-blade springs
- Adjustable side-wall scraper
- Extra-heavy safety grille, also closes off the mixing mechanism
- Water supplied through a hollow section in the safety grille
- Tight-sealing, easy-to-operate rear discharge slide
- Removable discharge chute
- Primed and finished with 2K paint
Technical data
| Manufacturer | FLIEGL |
|---|---|
| Product type | PTO-driven forced-action mixer |
| Capacity | 400 l |
| Output | approx. 7 m³/h |
| Power requirement | min. 40 PS |
| Filling diameter | 1.100 mm |
| Unladen weight | 430 kg |
| Gearbox | 2-speed, ratio 11:1 |
| Mounting | Category 2 three-point linkage (adjustable to 3 positions) and forklift |
| Internal forklift lug dimensions (L × W) | 190 × 60 mm |
| Mixer shaft bearings | 3-point |
| Finish | primed and finished with 2K paint |
Product description
400-litre forced-action mixer
The mixer uses a mixing mechanism inside a stationary hopper and achieves an output of around 7 m³/h. The hopper and mixing tools are made from highly wear-resistant steel, and the drive is powered by the PTO.
Forced-action mixer instead of free-fall mixer – the fundamental difference
The design is what determines the mixing quality.
| Free-fall mixer | Forced-action mixer | |
|---|---|---|
| Operating principle | Drum rotates, material falls | Mixing mechanism works inside a stationary hopper |
| Mixing time | longer | shorter |
| Earth-moist mixes | problematic | possible |
| Homogeneity | adequate | higher |
| Emptying | Tip the drum | Open the slide |
Why earth-moist mixes make the difference: A free-fall mixer needs enough water for the material to slide at all. Mixes that are too dry remain in the drum as lumps and are not mixed through.
The forced-action mixer works mechanically through the material – regardless of its consistency. This makes it suitable for applications such as screed, drainage concrete and earth-moist mortar, which cannot be mixed in a free-fall mixer.
The adjustable mixing mechanism – the key to a long service life
The mixing tools can be adjusted sideways and downwards.
Why this is necessary: During mixing, the tools scrape along the base and side wall. Both parts wear – increasing the gap between them.
What happens as the gap increases:
- Material remains on the base. It is no longer picked up and remains unmixed.
- Deposits build up on the wall and harden, permanently reducing the hopper's capacity.
- Mixing time increases, while quality decreases.
With a mixer that cannot be adjusted, the machine has reached the end of its service life at this point. Here, the tools can be adjusted – restoring full performance.
The adjustable side-wall scraper works on the same principle against the hopper wall.
The 3-blade springs
The mixing tools are mounted on particularly strong leaf springs, which can be adjusted to different angles.
What the spring suspension does: It presses the tools against the base and wall – and gives way when an obstacle is encountered.
Obstacles that may be found in the mixer: larger aggregate stones, hardened material residue or foreign objects added by mistake.
Without spring suspension, the full force would act on the tools, shaft and gearbox. With spring suspension, the tools give way and return to position.
The angle adjustment allows the tools to be adapted to the mix – a steeper angle gives more aggressive mixing, while a shallower angle is gentler.
The 11:1 gearbox
The two-stage reduction converts PTO speed to mixer speed.
The calculation: 540 rpm at the PTO gives around 49 rpm at the mixing mechanism.
Why this low speed is right:
- High torque. The mixing mechanism has to work through tough material – power matters here, not speed.
- No separation. At high speeds, material is flung outwards and separates by particle size.
- Less wear on the tools and hopper.
The gearbox's two-stage design distributes the reduction across two pairs of gears – reducing the load on each stage compared with a single-stage solution with the same ratio.
Two mounting options on one machine
| Mounting | Carrier vehicle |
|---|---|
| Category 2 three-point linkage | Tractor – adjustable to three positions |
| Forklift pockets | Forklift and telehandler |
What this combination offers: The mixer can be driven by the tractor and moved with a forklift – or carried by forklift to the work area and emptied there.
The three-position adjustable three-point linkage allows the working height to be adjusted – important because the discharge height determines what can fit underneath: a wheelbarrow, bucket or vehicle.
Please note: The drive is powered by the PTO. The machine can only be transported by forklift, not operated from it – unless the forklift is equipped with a PTO.
Water supplied through the safety grille
A detail that changes the workflow.
How it works: The safety grille is hollow and carries the water through.
Why this is practical:
- Even distribution. Water is delivered across the surface, rather than in one spot.
- No loose hose to get in the way when loading.
- Water can be added in measured amounts while mixing – without opening the grille.
Why adding water affects quality: The water-cement ratio determines the strength of the concrete. Too much water significantly reduces its strength – and this cannot be corrected.
Adding small, controlled amounts is therefore better than pouring in more from a bucket.
The safety grille
It is extra heavy-duty and also closes off the mixing mechanism.
Why this is more than a formality: A running mixing mechanism in an open hopper is a serious hazard. Anyone reaching inside – for example, to loosen a lump – could lose their hand.
The grille's heavy-duty construction has a second purpose: material hits it when loading with a shovel or loader. A lightweight grille can bend and then no longer close properly.
The discharge slide
The manufacturer highlights its particularly tight seal and smooth operation.
Why both properties matter:
- Tight-sealing: Nothing should escape during mixing. Cement-water mix leaking through the gap changes the mix and makes the work area dirty.
- Easy to operate: The slide works against the material pressing against it. A stiff slide becomes almost impossible to move after just a few batches, because cement slurry hardens in the guide.
The removable discharge chute directs the material precisely and can be removed for transport and cleaning.
The base reinforced in a star pattern
The reinforcement is positioned where the greatest loads occur.
The forces involved: The mixing mechanism presses against the base with spring force and moves over it continuously. At the same time, the base supports the weight of all the material.
The calculation: 400 litres of concrete weigh around 960 kg. The forces generated by the mixing action are additional – acting in changing directions with every rotation.
The star-shaped arrangement transfers the load from the centre outwards to the edge of the hopper, rather than leaving it concentrated on the base.
Protected mixer shaft bearings
This is where mixers typically fail.
The problem: The mixer shaft passes through the hopper base. It has to be sealed against fresh concrete while moving.
What happens if protection is inadequate: Cement slurry gets into the bearings, hardens there and destroys them. The damage only becomes apparent when the shaft develops play – at which point the tools scrape unevenly.
The three-point bearing arrangement further distributes the forces and keeps the shaft in position, even under uneven loads.
Filling diameter 1.100 mm
The large opening makes loading easier.
What this means in practice: The mixer can be filled with a shovel, loader or bagged material without spilling material over the side.
With a capacity of 400 litres and several batches a day, this adds up – every loading operation saves time and material.
7 m³ per hour – what this means in practice
| Capacity per batch | 400 l = 0.4 m³ |
|---|---|
| Output | approx. 7 m³/h |
| Calculated | around 17 batches per hour |
What this means: A batch is mixed and discharged in just over three minutes – including loading.
The actual figure is lower, as material preparation and processing also take time. But the figures show that the mixer is not the bottleneck – the work crew before and after it is.
Power requirement from 40 PS
This is a moderate requirement.
What this means in practice: The mixer can be used with compact tractors and smaller tractors – you do not need a large machine.
Please note: The 430 kg unladen weight plus up to 960 kg of material adds up to around 1,390 kg at the rear. The permitted implement load and lifting capacity must be sufficient – engine power alone is not enough to assess suitability.
PTO shaft with overload protection
It protects the drive train.
Against what: If the mixing mechanism jams – due to hardened material, a foreign object or a mix that is too stiff – the full engine torque acts on the gearbox and shaft.
What the protection does: It disconnects the drive before damage occurs. This is particularly important with a gearbox featuring an 11:1 reduction – the reduction also multiplies the torque when the mechanism jams.
Primed and finished with 2K paint
The surface finish consists of two layers.
Why this matters for a mixer: Fresh concrete is alkaline, cement slurry sticks to everything, and cleaning is carried out with a pressure washer.
2K paint is significantly more durable than single-component paint – it cures chemically rather than simply drying. The primer underneath also protects the steel where the topcoat is damaged.
Suitable mixes
- Concrete of all consistencies
- Mortar and plaster
- Screed
- Earth-moist mixes
- Dry mixes
Applications
Farms, construction companies and building contractors, landscaping and grounds maintenance, local authorities and public works depots, equestrian facilities, property maintenance services, equipment hire, small-scale precast concrete work.
Operating notes
- At least 40 PS and a PTO are required on the carrier vehicle.
- Check the permitted implement load and lifting capacity – when full, the mixer weighs around 1,390 kg.
- Category 2 three-point linkage; adjust the position to the required discharge height.
- When transporting by forklift, note the lug dimensions of 190 × 60 mm.
- Keep the safety grille closed while mixing – never reach into the running mixing mechanism.
- Switch off the PTO and wait for the machine to stop before opening the grille.
- Check the PTO shaft and safety devices before each use.
- Add water in measured amounts – too much water permanently reduces strength.
- Adjust the mixing tools and side-wall scraper as wear increases.
- Rinse thoroughly with water after every use – hardened concrete blocks the mixing mechanism and slide and is very difficult to remove.
- Clean the discharge slide and guide particularly carefully.
- Check the mixer shaft bearings regularly and lubricate as specified by the manufacturer.
- Do not stand beneath the raised mixer.
- Empty and store in a dry place in frosty conditions.
Frequently asked questions
What is the mixer's capacity?
400 litres, with a filling diameter of 1.100 mm. Output is around 7 m³/h – equivalent to approximately 17 batches per hour.
What tractor do I need?
At least 40 PS with a PTO. Lifting capacity is more important than engine power: when full, the mixer weighs around 1,390 kg.
What is the difference compared with a free-fall mixer?
In a forced-action mixer, a mixing mechanism works inside a stationary hopper. It mixes faster and more evenly, and can also handle earth-moist mixes – which remain as lumps in a free-fall mixer.
Can I operate the mixer from a forklift?
The forklift mounting is for transport and moving the mixer. The drive is powered by the PTO – the machine cannot be operated from a forklift without a PTO.
Why can the mixing mechanism be adjusted?
The tools and hopper wear, increasing the gap between them. Material then remains on the base and is no longer picked up. Adjusting the tools restores full mixing performance – mixers that cannot be adjusted have reached the end of their service life at this point.
How does water get into the mixer?
Through a hollow section in the safety grille. This distributes the water across the surface and allows it to be added in measured amounts while mixing – without opening the grille.
What is the gearbox ratio?
11:1, with a two-stage design. At 540 rpm at the PTO, this gives around 49 rpm at the mixing mechanism – low speed with high torque.
How heavy is the mixer?
430 kg empty. 400 litres of concrete adds around 960 kg.
| Gerätetyp : | Mischer |
|---|---|
| volume: | 400L |