ENOROSSI Front-Double-Action-Mähwerk 2,70 m, 530 kg, ab 70 PS
€7,187.00
Standard equipment
- Front-mounted Double-Action mower, working width 2.70 m
- Front-mounted, driven via the front PTO
- ‘Pull Back’ safety system with parallelogram
- Gearbox in oil bath
- Tie rod to prevent blade flutter
- Swath former (deflector)
- Lighting kit
- PTO shaft
- Complete spare blade
- Blade guard
Technical data
| Manufacturer | Enorossi (Enoagricola Rossi) |
|---|---|
| Product type | Mower with Double-Action cutter bar, front-mounted |
| Working width | 270 cm |
| Weight | approx. 530 kg |
| Power requirement | from 70 hp |
| Drive | Front PTO via PTO shaft, gearbox in oil bath |
| Working speed | 8 – 12 km/h |
| Min. cutting height | 3 cm |
| Working range | +90° to −45° from horizontal |
| Overload protection | ‘Pull Back’ system: cutter bar moves backwards and upwards via a parallelogram |
| Guards | bolted on, individually replaceable |
| Lighting | Lighting kit included as standard |
Product description
Front-mounted Double-Action mower
The mower is mounted at the front of the tractor and driven via the front PTO. With a 2.70 m working width, a weight of 530 kg and a power requirement from 70 hp, this is the front-mounted version of the range, for farms that want to combine cutter-bar mowing with a rear-mounted implement or keep the cutter bar in view while mowing.
The Double-Action principle – why it cuts rather than strikes
| Double-Action cutter bar | Rotary mower | |
|---|---|---|
| Cutting principle | shearing, like scissors | striking, free cut |
| Cut surface | smooth | ragged |
| Power requirement | low | high |
| Contamination in the forage | low | higher |
| Output per area | medium | high |
How the Double-Action cutter bar works: The upper and lower blades move in opposite directions, with each blade cutting against the opposing blade. The stem is cut through, not torn off. A clean cut surface closes more quickly, allowing the crop to regrow sooner.
Less dirt in the forage: Rotating discs create an airflow that draws soil and dust into the swath. The Double-Action cutter bar works without suction. Less soil means less crude ash and fewer clostridia, which cause faulty fermentation in the silo.
Insect-friendly mowing: The slow, shearing cut without suction kills considerably fewer insects than a striking cut. In agri-environment and contractual nature conservation schemes, cutter-bar mowing is often a funding requirement. Please check the conditions of your scheme.
Why front-mounted
| Rear-mounted | Front-mounted | |
|---|---|---|
| View of the cutter bar | Looking over your shoulder | directly in front of the driver |
| Rear linkage | occupied | free for a second implement |
| Driving over the cut crop | Wheels travel over uncut crop | Cutter bar mows ahead of the wheels |
- Forward visibility: At field edges, ditches, fences and obstacles, the driver can see the cutter bar directly without turning round. This reduces strain over a long working day.
- Rear linkage free: There is room at the rear for another implement, allowing two operations to be carried out in one pass.
- Weight distribution: A front-mounted implement acts as a counterweight to a heavy rear-mounted implement. Lifting capacity and axle loads must still be checked.
‘Pull Back’ – protection for front-mounted use
If the cutter bar hits an obstacle, the ‘Pull Back’ system moves it backwards and upwards via a parallelogram. It then returns to the working position. According to the manufacturer, the system also allows lateral oscillation.
Why this matters particularly at the front: A front-mounted implement encounters obstacles at full driving speed and before anything else. If the cutter bar moves backwards and upwards rather than remaining rigid, a stone, post or tree stump will not hit the cutter bar, frame and mounting bracket with full force.
Bolted guards
The guards are bolted on and individually replaceable. A damaged guard can be changed with a spanner instead of being drilled out and re-riveted. This helps keep the cutter bar working, particularly on stony ground.
Gearbox in oil bath
The drive runs through a gearbox in an oil bath.
Why this matters: The gearbox converts rotary motion into the oscillating movement of the blades, with alternating loads on every stroke. In an oil bath, the gears and bearings are continuously lubricated and cooled, reducing wear and maintenance.
+90° to −45° – the working range
| Position | Application |
|---|---|
| Horizontal | Meadows, grassland, lucerne |
| Downwards (up to −45°) | Ditch banks, sloping ground |
| Vertical (up to +90°) | Hedges, fence lines, vertical cuts |
The manufacturer recommends working in an inclined position only for short periods.
Lighting included as standard
A front-mounted implement with a width of 2.70 m obscures parts of the vehicle lighting when travelling on the road. The lighting kit is therefore included as standard equipment, making this the only version in the range with this feature.
Swath former
The deflector guides the cut crop to the side and lays it in a swath rather than spreading it out widely. This makes working with a tedder and rake easier.
Applications
Grassland and forage farms seeking clean forage, lucerne growers, agricultural contractors, local authorities and public works departments, ditch maintenance, landscape management, land under contractual nature conservation schemes, and farms combining front- and rear-mounted implements.
Operating notes
- Observe the power requirement: from 70 hp. The tractor needs a front linkage and front PTO.
- Check the lifting capacity of the front linkage, front axle load and steering capability. The implement weighs around 530 kg.
- Maintain the PTO speed specified by the manufacturer.
- Work in an inclined position only for short periods.
- Check the area for foreign objects before the first cut. The ‘Pull Back’ system does not remove the need for caution.
- Check blades and guards regularly for damage and replace them as necessary.
- Check the gearbox oil level as specified by the manufacturer.
- Fit the blade guard for transport and storage.
- Do not enter the working area, as objects may be ejected.
- Before working on the cutter bar, disengage the PTO, stop the engine and remove the key.
- When travelling on the road, connect the lighting kit and observe the requirements for the transport position, marking and permitted dimensions.
- Follow the manufacturer's operating instructions.
Frequently asked questions
What tractor do I need?
From 70 hp, with a front linkage and front PTO. The front lifting capacity and front axle load must be sufficient for an implement weighing around 530 kg.
What are the advantages of front mounting?
The driver can see the cutter bar directly in front, the rear linkage remains free for a second implement, and the cutter bar mows ahead of the wheels instead of the tractor driving over uncut crop.
What happens if it hits an obstacle?
The ‘Pull Back’ system moves the cutter bar backwards and upwards via a parallelogram, then returns it to the working position.
How far can the cutter bar be angled?
From +90° to −45°. The manufacturer recommends working in an inclined position only for short periods.
Is lighting included?
Yes, the lighting kit is included as standard equipment.
Are the guards bolted on or riveted?
They are bolted on and individually replaceable. A damaged guard can be changed with a spanner.
How fast can I travel?
A working speed of 8 to 12 km/h, according to the manufacturer.
What is included in the delivery?
PTO shaft, spare blade, blade guard, tie rod to prevent blade flutter, swath former and lighting kit.
| Cultivation method: | Frontanbau |
|---|---|
| Gerätetyp : | Mähwerk |
| Kraftbedarf: | ab 70PS |
| Working width: | 2,7m |