ENOROSSI Double-Action-Mähwerk 2,70 m, hydraulischer Aushub
€3,995.00
Scope of delivery
- 1 × Double-Action mower with 2.70 m working width, rear-mounted
- Hydraulic lift with lowering restrictor
- Safety device with automatic release on contact with an obstacle
- Tie rod to prevent blade flutter
- Relief spring on the inner skid
- Swath guide plate
- PTO shaft
- Spare blades
- Blade guard for transport and storage
- Operating instructions in German
Technical data
| Manufacturer | Enorossi (Enoagricola Rossi) |
|---|---|
| Type | Mower with Double-Action cutter bar (scissor cut, upper blade and counter-blade move in opposite directions) |
| Mounting | Rear-mounted, three-point linkage Cat. I and II |
| Working width | 270 cm |
| Weight | approx. 322 kg |
| Lift | hydraulic, with lowering restrictor |
| Drive | PTO via PTO shaft |
| Working speed | up to 12 km/h |
| Blades | individually replaceable |
| Stone protection | patented design with movable blades and fingers |
| Overload protection | automatic release of the cutter bar |
| Cutter bar working range | up to +90° for hedge cutting, slope angle +90° / −75° |
| Transport position | Cutter bar folds up and is secured with a retaining bar |
| Cutter bar guidance | two skids, inner shoe relieved |
| Construction | Pressed-steel construction with hardened bushes |
Product description
A Double-Action mower with a working width of 2.70 metres and a weight of 322 kilograms. Together, these two figures describe what this machine is all about: a working width normally associated with heavy disc mowers, at a fraction of the weight and requiring a fraction of the power.
Scissor cut instead of impact cut – the difference starts at the stem
A rotary or disc mower cuts the stem with a high peripheral speed. A Double-Action cutter bar cuts it like a pair of scissors: the upper and lower blades move in opposite directions, guide the stem between them and cut it cleanly.
This has an impact on four things at once:
- Power requirement. There is no heavy rotating mass to accelerate and keep turning. The power required at the PTO is significantly lower than that of a disc mower of the same width, resulting in correspondingly lower diesel consumption.
- Cut quality. A cleanly cut stem dries quickly at the cut surface. A crushed stem loses cell sap and becomes an entry point for fungi. Regrowth is faster and more even.
- Feed cleanliness. The cutter bar works close to the ground but does not stir up soil, as no discs are rotating. Less soil in the feed means lower crude ash levels and less Clostridia contamination. This matters for silage quality and for farms supplying milk to cheesemakers, as Clostridia spores cause late blowing in cheese. A soil-free cut is also an advantage for clean hay, for example in hay milk production.
- Insect protection. The slow, cutting action without suction kills considerably fewer insects than an impact cut with airflow. In agri-environment and contractual nature conservation schemes, cutter bar mowing is often a funding requirement. Please check the specific scheme conditions in your region.
322 kilograms – why weight is the real selling point
The low weight has an impact in three areas, and all three would otherwise cost money.
On the ground: A lightweight implement allows you to use a lighter tractor. Less total weight on the field means less compaction. On wet ground, peat grassland and wet pastures, this is not a minor consideration but a prerequisite for being able to drive at all.
On slopes: The lighter the mounted implement, the greater the stability of the combination. The cutter bar also works down to −75 degrees and therefore follows ditches, banks and changes in terrain.
On the tractor: The 322 kilograms are not centred but hang far out to the right on the rear linkage. This is where the choice of tractor is decided, based on lifting capacity, unladen weight and stability, not horsepower. A sufficiently heavy tractor with front ballast is more important here than a powerful engine. Please check the lifting capacity of your linkage and the permitted rear axle load before purchase; we will be happy to advise you.
Individually replaceable blades – the difference compared with the riveted version
This feature sets this range apart from the manufacturer's simpler Double-Action mowers, and makes a difference throughout the machine's service life.
With riveted blades, each blade is permanently attached to the knife back. If a stone, wire or molehill damages a blade, it must either be re-riveted or the complete knife replaced.
With this version, the blades can be replaced individually. The damaged blade is released and replaced in the field, using the tools carried on board, in minutes rather than an hour in the workshop. For a wear part that encounters stones every season, this makes up for the extra cost compared with the riveted version.
Stone protection and overload protection
The cutter bar works close to the ground and encounters anything lying there. Two independent safeguards are provided for this.
The patented stone protection uses movable blades and fingers: smaller foreign objects are pushed out rather than becoming lodged in the cutter bar. This prevents the most common operating problem with a Double-Action cutter bar.
The automatic release comes into play when larger obstacles are encountered: if the cutter bar hits a post, stone or tree stump, the safety device gives way and the cutter bar swings out instead of breaking. This is the difference between a one-minute interruption and a bent cutter bar.
The hydraulic lift with lowering restrictor
The cutter bar is raised hydraulically and folded into the transport position, where it is secured by a retaining bar. With a cutter bar length of 2.70 metres, this is the only sensible solution. The smaller models in the range are still available with a mechanical lift as an option; from 2.40 metres upwards, they are not.
The lowering restrictor is the detail that matters in everyday use: It slows the lowering process so that the cutter bar moves into the working position in a controlled manner instead of dropping suddenly. Without a restrictor, a 2.70 m cutter bar slams down when lowered. This puts strain on the mounting components, skids and turf.
The cutter bar can also be raised to +90 degrees. This allows hedge cutting and mowing banks above the driving track, as regularly encountered in roadside, watercourse margin and landscape maintenance.
Cutter bar guidance and swath placement
The cutter bar runs on two skids and therefore follows uneven ground. A relief spring on the inner shoe takes weight off the turf. Without it, the inner skid would cut into soft ground.
The tie rod to prevent blade flutter keeps the cutter bar on track. Flutter is the main problem with long cutter bars: a vibrating cutter bar cuts unevenly and causes disproportionate wear to the blade guide.
The swath guide plate deposits the cut material in a defined row instead of spreading it widely. This is important for the subsequent work with a rotary tedder or swather.
Applications
Grassland and forage production where clean feed is important, wet and peatland sites, slopes, traditional orchards, extensive areas under contractual nature conservation, landscape and roadside maintenance, watercourse margins, horse hay, and farms producing hay milk or milk for cheesemaking.
Operating notes
- Check the tractor's lifting capacity and stability before purchase. The 322 kg is positioned well off-centre; front ballast is generally required.
- Check the PTO shaft length and fit all guards correctly.
- Check the blades regularly for wear and correct seating. Blunt blades crush rather than cut and increase the power requirement.
- Always fit the blade guard for transport and storage.
- Before working on the cutter bar, disengage the PTO, stop the engine and remove the key. Secure the implement against lowering.
- Check the field for posts, wire and stones before the first cut. The release mechanism protects the cutter bar but does not replace an inspection.
Frequently asked questions
What tractor do I need for this?
With this implement, the tractor itself is more important than engine power: the mower weighs around 322 kg and is mounted well off-centre on the rear linkage. Lifting capacity, unladen weight and stability are therefore key, and front ballast is generally required. A Double-Action mower requires significantly less PTO power than a disc mower of the same width because no heavy masses rotate. Please contact us before purchase to check the specific power and lifting capacity requirements.
What is the difference between a Double-Action mower and a disc mower?
It is the cutting principle. A disc mower cuts the stem at high speed. With a Double-Action cutter bar, the upper and lower blades move in opposite directions and cut the stem with a scissor action. This results in lower power and diesel requirements, a cleaner cut with faster regrowth, less soil contamination in the feed and significantly greater protection for insects.
What does the hydraulic version mean?
The cutter bar is raised hydraulically and folded into the transport position. A lowering restrictor slows the descent so that the cutter bar moves into the working position in a controlled manner. At this working width, the hydraulic lift is the only version available. Only the smaller models in the range are also available with a mechanical lift.
What happens if the cutter bar hits an obstacle?
An automatic safety device gives way and allows the cutter bar to swing out instead of breaking. In addition, patented stone protection with movable blades and fingers pushes smaller foreign objects out rather than allowing them to become lodged in the cutter bar.
Can the blades be replaced individually?
Yes. On this version, the blades can be replaced individually. A damaged blade is released and replaced without changing the complete knife. This is not possible with riveted versions. A spare knife is included in the scope of delivery.
Can I use it to cut hedges and banks?
The cutter bar can be raised to +90° and works on slopes down to −75°. This allows hedge cutting and mowing banks above and below the driving track, for example during roadside and watercourse margin maintenance.
Is the mower suitable for areas under contractual nature conservation?
Cutter bar mowing is considered particularly insect-friendly and is often specified or required as a method in agri-environment and contractual nature conservation schemes. The specific requirements vary depending on the region and scheme. Please check your scheme's conditions before purchase.
How is the mower driven?
Via the tractor's PTO using a PTO shaft. The PTO shaft is included in the scope of delivery and must be checked for the correct length before first use.
Why is the feed cleaner than with a rotary mower?
Because no discs rotate, there is no airflow to stir up soil. Less soil contamination means lower crude ash levels and fewer Clostridia in the feed. This improves silage quality and is important for milk used in cheesemaking, as Clostridia spores cause late blowing in cheese.
| Cultivation method: | Heckanbau |
|---|---|
| Gerätetyp : | Mähwerk |
| Kraftbedarf: | ab 50PS |
| Working width: | 2,7m |