Skip to main content Skip to search Skip to main navigation
Menu

ENOROSSI Double-Action-Mähwerk 2,40 m, hydraulischer Aushub, ab 50 PS

Description

Scope of delivery

  • 1 × Double-Action mower with 2.40 m working width, rear-mounted
  • Hydraulic lift
  • Mechanical safety device that trips on contact with an obstacle
  • Anti-flutter tie rod
  • Compensation springs
  • Swath former
  • PTO shaft
  • Complete replacement knife
  • Knife guard for transport and storage

Technical data

ManufacturerEnorossi (Enoagricola Rossi)
DesignMower with Double-Action cutter bar (scissor cut, upper blade and counter-blade move in opposite directions)
MountingRear-mounted, three-point linkage Cat. I and II
Working width240 cm
Power requirementfrom 50 hp
Weightapprox. 305 kg
Lifthydraulic
DrivePTO via PTO shaft, three-belt drive with belt tension spring
Working speed8–12 km/h
Minimum cutting height3 cm
Bladesindividually replaceable
Guardsbolted on
Overload protectionmechanical safety device
Cutter bar working range+90° to −45°
Cutter bar guidanceSkid, adjustable to three positions, outer shoe, compensation springs

Product description

A Double-Action mower with a working width of 2.40 metres, weighing around 305 kg and suitable for tractors from 50 hp. It sits between the compact sizes for small tractors and the 2.70 m version, offering the typical capacity required by a medium-sized grassland farm.

Scissor cut instead of impact cut – the difference starts at the stem

A rotary or disc mower cuts the stem with a high peripheral speed. A Double-Action cutter bar cuts it like a pair of scissors: the upper and lower blades move in opposite directions, guide the stem between them and cut it cleanly.

This has an impact on four things at once:

  • Power requirement. There is no heavy rotating mass to accelerate and keep turning. Despite its 2.40 m working width, it requires just 50 hp, with correspondingly low diesel consumption.
  • Cut quality. A cleanly cut stem dries quickly at the cut surface. A crushed stem loses cell sap and becomes an entry point for fungi. Regrowth is faster and more even.
  • Feed cleanliness. The cutter bar works close to the ground but does not throw up soil, as no discs rotate. Less soil in the feed means lower crude ash content and less clostridia contamination. This matters for silage quality and for farms supplying milk to cheesemakers, as clostridial spores cause late blowing in cheese. A soil-free cut is also beneficial for clean hay, for example for horses or hay milk production.
  • Insect protection. The slow, cutting action without suction kills considerably fewer insects than an impact cut with airflow. In agri-environment and contractual nature conservation schemes, cutter-bar mowing is often a funding requirement. Please check the specific scheme conditions in your region.

2.40 metres at 305 kg – why weight is the real selling point

The low weight makes a difference in three areas, and all three would otherwise cost money.

On the ground: A lightweight implement allows you to use a lighter tractor. Less total weight on the field means less compaction. On wet ground, peat grassland and wet pastures, this is often what makes it possible to drive at all.

On slopes: The lighter the mounted implement, the more stable the combination. The cutter bar works down to −45 degrees and can therefore follow ditches and embankments.

On the tractor: The 305 kg is not centred, but hangs well out to the right on the rear linkage. In addition to the minimum power requirement of 50 hp, the tractor’s lifting capacity, kerb weight and stability are therefore important. A sufficiently heavy tractor with front ballast is more important here than a powerful engine. Please check the lifting capacity and permitted rear axle load before purchase; we will be happy to advise you.

Individually replaceable blades – the difference from the riveted version

This feature sets this range apart from the manufacturer’s simpler Double-Action mowers, and makes a difference throughout the implement’s service life.

With riveted blades, each blade is permanently attached to the knife back. If a stone, wire or molehill damages a blade, it must either be re-riveted or the complete knife replaced.

On this version, the blades can be replaced individually. The damaged blade is released and replaced in the field, using the tools carried on board, in minutes rather than taking an hour in a workshop. The guards are also bolted on and can be replaced individually.

Mechanical safety device

If the cutter bar hits a post, stone or tree stump, the safety device gives way and the bar swings out instead of breaking. That is the difference between a one-minute interruption and a bent cutter bar. According to the manufacturer, the system is also suitable for stony ground.

Hydraulic lift

The cutter bar is raised hydraulically and folded into the transport position. From a working width of 2.40 metres, hydraulic lift is the only version available. The smaller sizes up to 2.10 metres are also available with mechanical lift.

Why this matters at this width: A 2.40 m cutter bar is difficult to lift by hand. With hydraulic lift, the driver can raise it from the seat at fence posts, around tree bases, at crossings and over ditch culverts, without getting out.

The cutter bar can also be raised to +90 degrees. This makes hedge cutting and mowing embankments above the driving track possible, for example when maintaining roadside verges, watercourse margins and landscapes.

Cutter bar guidance and swath placement

The skid is adjustable to three positions and determines the cutting height, down to a minimum of 3 cm. The outer shoe helps the cutter bar enter the crop instead of pushing it down. Compensation springs take weight off the cutter bar so that it does not cut into soft ground.

The anti-flutter tie rod keeps the cutter bar on track. Flutter is the main problem with long cutter bars: a vibrating bar cuts unevenly and causes excessive wear to the knife guide.

The swath former lays the cut crop in a defined row instead of spreading it out. This is important for the subsequent work with a rotary tedder or swather.

Range overview

Working widthWeightPower requirementLift
1.65 m256 kgfrom 35 hpmechanical or hydraulic
1.80 m264 kgfrom 35 hpmechanical or hydraulic
2.10 m287 kgfrom 35 hpmechanical or hydraulic
2.40 m305 kgfrom 50 hphydraulic
2.70 m322 kgfrom 50 hphydraulic

Weights up to 2.10 m without lift; approx. +11 kg with mechanical lift and approx. +16 kg with hydraulic lift.

Applications

Grassland and forage production where clean feed is important, wet and peatland sites, slopes, traditional orchards, extensive areas under contractual nature conservation, landscape and roadside verge maintenance, watercourse margins, horse hay production, and farms producing hay milk or milk for cheesemaking.

Operating notes

  • Check the tractor’s lifting capacity and stability before purchase. The 305 kg hangs well off-centre, so front ballast is generally required.
  • Check the PTO shaft length and fit all guards correctly.
  • Check the blades regularly for wear and secure fit. Blunt blades crush rather than cut and increase power requirements.
  • Check belt tension at the start of the season.
  • Always fit the knife guard for transport and storage.
  • Before working on the cutter bar, disengage the PTO, stop the engine and remove the key. Secure the implement against lowering.
  • Check the field for posts, wire and stones before the first cut. The safety device protects the cutter bar, but does not replace an inspection.

Frequently asked questions

What tractor do I need?

The power requirement starts at 50 hp. Lifting capacity, kerb weight and stability are just as important: the mower weighs around 305 kg and hangs well off-centre on the rear linkage, so front ballast is generally required. If in doubt, please contact us before purchase.

What is the difference between a Double-Action mower and a disc mower?

It is the cutting principle. A disc mower cuts the stem at high speed. With a Double-Action cutter bar, the upper and lower blades move in opposite directions and cut the stem with a scissor action. This results in lower power and diesel requirements, a cleaner cut and faster regrowth, less soil contamination in the feed and considerably better insect protection.

Is this working width also available with mechanical lift?

No. From a working width of 2.40 m, only hydraulic lift is available. The smaller sizes up to 2.10 m are also available with mechanical lift.

What happens if the cutter bar hits an obstacle?

A mechanical safety device gives way and allows the cutter bar to swing out instead of breaking.

Can the blades be replaced individually?

Yes. A damaged blade can be released and replaced without changing the complete knife. The guards are also bolted on. A complete replacement knife is included in the scope of delivery.

Can I use it to cut hedges and embankments?

The cutter bar can be raised to +90° and lowered to −45°. This makes it suitable for cutting hedges and mowing embankments above and below the driving track.

How low does the mower cut?

The minimum cutting height is 3 cm. It is set using the skid, which is adjustable to three positions.

Is the mower suitable for areas under contractual nature conservation?

Cutter-bar mowing is considered particularly insect-friendly and is often included or required as a method in agri-environment and contractual nature conservation schemes. The specific requirements vary by region and scheme. Please check your scheme conditions before purchase.

Properties
Cultivation method: Heckanbau
Gerätetyp : Mähwerk
Kraftbedarf: ab 50PS
Working width: 2400mm