Skip to main content Skip to search Skip to main navigation
Menu

ENOROSSI Double-Action-Mähwerk 2,10 m, Dreipunkt, ab 30 PS

Description

Standard equipment

  • PTO shaft
  • Spare blade
  • Blade guard
  • Mechanical break-back protection
  • Adjustable outer shoe
  • Swath former (metal deflector)
  • Tie rod to prevent blade flutter

Choose when ordering: mechanical or hydraulic lift.

Technical data

ManufacturerEnorossi
Product typeMower with double-action cutter bar, rear-mounted
Working width210 cm
Weightapprox. 287 kg
Power requirement30 – 75 PS
Working speed8 – 12 km/h
Min. cutting height3 cm
Working range+90° to −45° from horizontal
MountingCategory I and II three-point linkage
Liftmechanical or hydraulic
Frame and mounting bracketFE 510 steel
Drive3 V-belts on three-groove ductile iron pulleys
Drive shafthardened 39NiCrMo3 steel
Bladesself-sharpening, riveted sections
Outer shoeductile iron, adjustable
Guardsbolted, individually replaceable

Product description

Double-action mower with 2.10 m working width

The double-action cutter bar achieves high working speeds without clogging and guarantees a precise, clean cut. The angle of inclination ranges from +90° to −45°. This allows you to work on ditches, banks and hedges as well as level ground.

The double-action principle – why it cuts rather than strikes

This is the fundamental difference compared with a rotary mower.

Double-action cutter barRotary mower
Cutting principleshearing, like scissorsstriking, free cut
Cut surfacesmoothragged
Power requirementlowhigh
Contamination of foragelowhigher
Area outputmediumhigh

How the double-action cutter bar works: The upper and lower blades move in opposite directions, with each blade cutting against the other.

What this means for the crop:

  • Smooth cut surface. The stem is cut through, not torn off.
  • Faster recovery. A clean wound closes faster than a ragged one.
  • Less drying out at the cut.
  • Higher subsequent yields thanks to faster regrowth.

The difference is particularly noticeable with lucerne: The stems are barely damaged by the sharp blades, and regrowth is faster than with other cutting methods.

Less dirt in the forage

This is the most important point for forage quality.

Why rotary mowers introduce dirt: The rotating discs create a strong draught. Soil, dust and material from molehills are stirred up and end up in the swath.

The double-action cutter bar works without suction. It draws significantly less dust and dirt into the swath.

What crude ash in forage means:

  • Lower energy density. Soil has no feed value.
  • Poorer ensilability. Soil bacteria cause undesirable fermentation.
  • Higher risk of clostridia. A quality issue in dairy farming.
  • More wear on harvesting equipment and feed mixers.

For farms with high forage-quality requirements, this is the reason to choose a double-action mower.

Moving blades and moving guards

This is what makes Enorossi special.

What makes it different: On a conventional finger bar, the guards are fixed and only the blade moves. Here, both move in opposite directions.

The practical effect: Almost no stones get into the cutter bar. Material that would otherwise get between the blades is pushed out by their opposing movement.

Why this determines service life: A stone between the blade and the counter-edge damages both. On stony ground, this is the most common cause of damage to cutter-bar mowers.

+90° to −45° – the working range

The bar can be swung well beyond the horizontal.

PositionApplication
HorizontalMeadows, grassland, lucerne
Downwards (−45°)Ditch banks, sloping ground
Vertical (+90°)Hedges, fence lines, vertical cutting

What this means in practice: One machine for meadows, ditches and hedges. For local authorities, public works departments and businesses maintaining ditches, it replaces a second machine.

The manufacturer specifically mentions use for ditch clearance and vertical trimming.

Low power requirement – the key to economy

The mower can be used with tractors from 30 PS.

Why a double-action cutter bar needs so little power: With a shearing cut, only the cutting force is required. A rotary mower also has to keep the discs spinning at high speed. A considerable proportion of the power is used to overcome inertia.

The result:

  • Smaller tractors are sufficient. The manufacturer highlights that its compact design allows it to be used with lower-powered tractors.
  • Lower fuel consumption per hectare.
  • Less ground pressure, because a smaller tractor is sufficient.
  • Lower operating costs overall.

For part-time farms, horse owners and hilly areas, this is often the deciding factor. A 100 PS tractor is not available in these situations.

Break-back protection

All cutter bars are fitted with an automatic safety release.

What it does: If the bar hits an obstacle, it swings back automatically instead of transferring the force to the bar, frame and mounting bracket.

Why it is essential on grassland:

  • Stones and boulders are hidden in tall crops.
  • Posts and fence remains stand at the edge.
  • Tree stumps and roots lie along ditch edges.
  • Molehills conceal foreign objects.

Without break-back protection, hitting an obstacle at 12 km/h can bend the bar and, in the worst case, damage the mounting bracket.

Bolted guards

This distinguishes this version from the two smallest sizes in the range.

Working widthGuards
from 1.65 m (this version)bolted, individually replaceable
1.35 m and 1.50 mriveted

Why bolted guards are more economical in operation: A damaged guard can be replaced individually using a spanner, rather than a rivet hammer and removing the cutter bar.

What this means during the season: A bent guard brings the bar to a standstill. If you can replace it in the field, you can carry on mowing instead of going to the workshop.

Material selection

The manufacturer specifies the materials used.

ComponentMaterialReason
Frame and mounting bracketFE 510high-strength structural steel for the load-bearing structure
Drive shaft39NiCrMo3, hardenedhigh-strength quenched and tempered steel
Pulleysductile irontougher than grey cast iron, fracture-resistant
Outer shoeductile ironwear-resistant component close to the ground
Bladeshigh-quality steel, self-sharpeningstay sharp during operation

Why the drive shaft is subject to particular stress: It converts rotary motion into the reciprocating movement of the blades. The direction of force reverses with every stroke. This alternating load is more than standard steel can withstand over time.

The belt drive

Three V-belts transmit the power.

What else the belt drive does: It acts as an overload protection system. If the bar suddenly jams, the belts slip instead of transferring the force to the drive train.

The second advantage: Belts dampen the vibrations that inevitably occur with an oscillating blade drive.

Maintenance: V-belts are wear parts and their tension must be checked. Loose belts slip and burn, while belts that are too tight put strain on the bearings.

Self-sharpening blades

The blades with riveted sections stay sharp during operation.

How it works: The blades run against each other. Constant contact keeps the cutting edges sharp, much like a pair of scissors.

Why sharpness matters particularly here: A blunt blade crushes rather than cuts. The stem is crushed instead of being cut through, which is precisely what delays regrowth.

A spare blade is included, a real advantage during the season.

Outer shoe and swath former

The adjustable outer shoe guides the bar along the ground and helps it enter the crop instead of pushing it down. It is made of wear-resistant ductile iron.

The metal swath former guides the cut material to the side instead of leaving it spread out. This makes working with a tedder and rake easier.

3 cm minimum cutting height

The bar cuts close to the ground.

When this is desirable: with lucerne and for the first cut, when every centimetre of growth counts.

When the cut should be higher: In practice, a cutting height of 6 to 8 cm is generally considered suitable for grassland. Cutting too low weakens the sward and brings soil into the forage.

Being able to adjust the height upwards is therefore more important than the minimum.

Applications

Grassland farms, horse keeping and haymaking, lucerne growing, part-time farms, organic farms, hilly and mountainous areas, local authorities and public works departments, ditch maintenance, landscape management, traditional orchards.

Operating notes

  • Observe the power requirement: 30 to 75 PS. Category I or II three-point linkage.
  • Check the tractor's lifting capacity and rear axle load. Consider front ballast when rear-mounted.
  • Maintain the PTO speed specified by the manufacturer.
  • Adjust the cutting height to suit the crop. Cutting too low weakens the sward and brings soil into the forage.
  • Check the field for foreign objects before the first cut. Break-back protection does not remove the need for caution.
  • Check the blades regularly for damage; replace damaged blades and guards.
  • Check V-belts for tension and wear.
  • Lubricate grease points as specified by the manufacturer. The oscillating drive requires frequent lubrication.
  • Fit the blade guard for transport and storage.
  • Do not enter the working area, as objects may be ejected.
  • Before working on the bar, disengage the PTO, stop the engine and remove the key.
  • When driving on the road, observe the requirements for transport position, lighting, marking and permitted dimensions.
  • Follow the manufacturer's operating instructions.

Frequently asked questions

What tractor power do I need?

30 to 75 PS according to the manufacturer's table. The low power requirement is a key advantage of the double-action cutter bar, which can also be used with lower-powered tractors.

What are the advantages over a rotary mower?

The shearing cut leaves a smooth surface, the crop recovers faster, and significantly less dust and soil gets into the forage. The trade-off is lower area output.

How far can the bar be swung?

From +90° to −45° from horizontal. This allows you to mow meadows, work on ditch banks and trim hedges vertically with one machine.

What happens if it hits an obstacle?

The automatic break-back protection releases the bar instead of transferring the force to the frame and mounting bracket.

Are the guards bolted or riveted?

They are bolted and individually replaceable. A damaged guard can be changed with a spanner. Only the two smallest sizes in the range, 1.35 and 1.50 m, have riveted guards.

Why do hardly any stones get into the cutter bar?

Because both the blades and the guards move. Material that would otherwise get between the blades is pushed out by their opposing movement.

How fast can I travel?

8 to 12 km/h. The double-action cutter bar achieves high working speeds without clogging.

What is included in the delivery?

The PTO shaft, spare blade and blade guard are included as standard. The lift is selected as mechanical or hydraulic when ordering.

Properties
Cultivation method: Heckanbau
Gerätetyp : Mähwerk
Kraftbedarf: ab 35PS
Working width: 2,10m