ENOROSSI Double-Action-Mähwerk 1,80 m, 264 kg, ab 30 PS, Heckanbau
€2,990.00
Scope of delivery
- 1 × Double-Action mower, working width 1,800 mm
- PTO shaft
- Complete replacement cutter bar
- Blade guard for transport and storage
- Mechanical safety release
- Pull rod to prevent blade flutter
- Category I or II three-point linkage mounting
Choose when ordering: mechanical or hydraulic lifting.
Technical data
| Manufacturer | Enoagricola Rossi, Italy |
|---|---|
| Design | Rear-mounted mower with Double-Action cutter bar |
| Working width | 1,800 mm |
| Weight | 264 kg |
| Tractor power required | from 30 PS |
| Working speed | up to 15 km/h |
| Cutting angle | +90° to −45° |
| Blade strokes | 1,080 strokes/min at 540 min-1 PTO speed |
| Mower fingers | bolted, individually replaceable |
| Drive | 3-belt drive with tension spring |
| Weight relief | Relief spring |
| Skid | adjustable to 3 positions |
| Outer shoe | for better penetration into the crop |
| Swath formation | Metal deflector |
| Control support | Pressed steel with hardened bushes |
| Mounting | Category I or II three-point linkage |
| Lifting | mechanical or hydraulic, selectable |
| Other widths | 1,650, 2,100, 2,400 and 2,700 mm |
Product description
A Double-Action mower cuts, whereas a rotary mower beats the crop. This is not a minor design detail; it is the reason for everything that makes this machine different: lower power requirements, less fuel, cleaner forage and a cut that does not damage the sward.
With a 1.80 m working width, a weight of 264 kg and a power requirement of 30 PS, this model is designed for small and medium-sized tractors: orchards, traditional orchards, municipal areas, horse paddocks, part-time farms and agri-environment schemes.
How the scissor cut works
With the Double-Action cutter bar, the upper and lower blades move against each other; both are in motion. Each stem passes between two closing cutting edges and is cut through like a pair of scissors.
The difference compared with the other two designs:
- Single-action finger bar: A blade moves against stationary fingers. It works, but the fingers clog in damp or lodged crops.
- Rotary mower: Freely swinging blades cut the stems through impact at high peripheral speed. Robust and fast, but it is a blow, not a cut.
- Double-Action cutter bar: A true scissor cut. And because both blades move, each one only has to reach half the speed. The result is lower inertial forces, less vibration and a much smoother run.
The blades make 1,080 strokes per minute at a PTO speed of 540 rpm, i.e. two cuts per PTO revolution.
30 PS for 1.80 metres – how it works
A rotary mower of the same working width requires considerably more power because it has to keep its blades at high peripheral speed at all times. The energy goes into rotation, not cutting.
A cutter bar only needs power to cut. This has three benefits:
- Small tractors are sufficient. 30 PS is available on almost every older tractor and every narrow-track tractor. If you thought a 1.80 m mowing width required a larger tractor, you do not need a new one.
- Diesel consumption per hectare is considerably lower. For areas mown several times a year, this means ongoing cost savings.
- 264 kg is light. This puts less strain on the linkage and front axle, and allows use where ground pressure is a concern.
Up to 15 km/h – challenging an old misconception
Cutter bars are considered slow. This machine is approved for working speeds of up to 15 km/h. That is within the range of speeds used with a rotary mower on the same area.
Once again, the reason is the Double-Action design: because both blades work, the cutting frequency is high enough to cut continuously at working speed. A single-action finger bar would need to run at twice the blade speed to do this.
Bolted mower fingers – what sets this range apart
Enorossi builds the same mower family in two versions: with riveted or bolted mower fingers. This machine has the bolted version, and that is the difference between a repair in the field and one in the workshop.
What happens if a finger breaks: On stony ground, molehills and where there is hidden wire, a finger will eventually break. With the riveted version, the rivet has to be drilled out and a new one fitted, using a drill, dolly and riveting tool – in other words, in the workshop.
A bolted finger can be replaced with two spanners at the edge of the field in ten minutes, using parts from the box behind the seat. For a machine working in unfamiliar terrain and on stony ground, that is the difference between finishing the job and having to stop.
From +90° to −45°: three machines in one
The bar can pivot from vertically upwards (+90°) to 45° downwards. This allows three different jobs to be done with the same machine:
- Horizontal: Meadows, pasture, orchards – the usual application.
- Up to 45° downwards: Banks, ditch edges, pond banks and verges. The bar follows the slope while the tractor stays on the track above.
- Vertically upwards: Vertical cutting along hedges, rows of trees and fence lines. For hedge maintenance, cutting rather than beating is gentler on the vegetation and gives a neater finish.
For local authorities and contractors, this is the real reason to buy: one machine for meadows, ditches and hedges instead of three attachments.
Forage quality: lower crude ash, faster regrowth
Two benefits that do not appear on the data sheet but make a difference in the livestock shed:
Crude ash. A rotary mower creates an airflow that draws soil and dust into the swath. A cutter bar does not create this suction; it cuts and lays the crop down. Less soil in the forage means lower crude ash. Less soil also means fewer clostridia enter the silo and cause faulty fermentation.
Regrowth. A cleanly cut stem heals quickly. A crushed or frayed stem dries out from the cut surface and regrows later. On areas cut several times a year, this adds up to a measurable yield.
Conservation areas
Cutter bars are considerably kinder to insects than rotary systems because they create no suction and operate at a lower tool speed. For agri-environment schemes, flower-rich areas, compensation areas and extensively managed grassland, this is now often a requirement or a condition of funding.
Check your funding scheme: Where a cutting machine is required, this mower is not the more expensive alternative – it is the only permitted option.
Safety release and drive
The bar has a mechanical safety release: if it hits a solid obstacle, it folds back instead of breaking. On a 1.80 m-wide bar working close to the ground, with its tip out of the driver's sight, this is the feature that keeps the machine working.
The machine is driven by a 3-belt drive with a tension spring. The belts also provide a second safeguard: they slip before anything breaks. Check belt tension at the start of the season. A belt that is too loose reduces cutting performance before it starts slipping.
The relief spring takes weight off the bar so that it follows the ground without digging in. The skid, adjustable to three positions, sets the cutting height. The outer shoe helps the bar enter the crop instead of pushing it down.
Mechanical or hydraulic lifting?
The machine is available in both versions. The choice depends on how you use it:
- Mechanical: cheaper, with no spool valve required. The right choice if the mower travels to the area, works there and then returns to the yard.
- Hydraulic: The driver can lift it from the seat. The right choice if it needs to be lifted frequently: around fence posts, tree bases, crossings and ditch culverts. For municipal and contract work, it pays for itself in a morning.
An honest look at the limitations
A Double-Action cutter bar is not superior to a rotary mower in every respect:
- It is more sensitive to stones, molehills and foreign objects. The safety release protects the bar, but fingers and blades are wear parts that need replacing more often on stony ground.
- It needs sharp blades. Blunt blades crush rather than cut, removing its main advantage. The replacement cutter bar supplied is not an accessory; it is part of the operating concept.
- It has no conditioner. If you need short field-drying times, you will need a separate operation.
- A rotary mower is better suited to heavily lodged, wet material at full speed.
Where it excels: Extensive grassland, orchards, traditional orchards, municipal areas, horse paddocks, conservation areas, ditches and hedges – and anywhere the tractor available is small.
Frequently asked questions
What tractor do I need?
From 30 PS and a Category I or II three-point linkage. At an unladen weight of 264 kg, the linkage is not under undue strain. The low power requirement is the main advantage of this design; a rotary mower of the same width requires considerably more.
What is a Double-Action mower, and how does it differ from a finger bar?
With the Double-Action cutter bar, the upper and lower blades move against each other; both are in motion. This is a true scissor cut. With a single-action finger bar, one blade moves against stationary fingers, which clog in damp or lodged crops. Because both blades work, the Double-Action bar runs more smoothly and cuts continuously at higher working speeds.
How fast can I travel?
Up to 15 km/h working speed, according to the manufacturer. The misconception that cutter bars are slow does not apply to this design.
What does “bolted mower fingers” mean?
The fingers are bolted, not riveted. A broken finger can be replaced at the edge of the field with two spanners, instead of being drilled out and riveted on again in the workshop. This is the key difference on stony ground.
Can I use it to cut banks and hedges?
Yes. The bar pivots from vertically upwards (+90°) to 45° downwards. This allows you to mow banks, ditch edges and verges, and cut hedges and rows of trees vertically, using the same machine as for the meadow.
Mechanical or hydraulic lifting?
Mechanical lifting is cheaper and does not require a spool valve, making it the right choice if the mower is lifted infrequently. Hydraulic lifting allows the driver to raise it from the seat and is the more economical option when lifting frequently around fence posts, tree bases and crossings.
Why is the cut better for the forage?
There are two reasons: a cutter bar creates no airflow suction, so it draws less soil into the swath. This lowers crude ash and means fewer clostridia enter the silo and cause faulty fermentation. Also, a cleanly cut stem heals faster, whereas a crushed stem dries out from the cut surface and regrows later.
Is the mower suitable for conservation areas?
Yes. Cutter bars are considerably kinder to insects than rotary systems because they create no suction and operate at a lower tool speed. A cutting machine is often a requirement for agri-environment schemes and funding programmes. Check your scheme.
Which wear parts need replacing?
Blades and mower fingers. A complete replacement cutter bar is included in the scope of delivery. This is not an accessory but part of the operating concept, because blunt blades crush rather than cut. Also check the tension of the three drive belts at the start of the season.
| Cultivation method: | Heckanbau |
|---|---|
| Gerätetyp : | Mähwerk |
| Kraftbedarf: | ab 35PS |
| Working width: | 1.80m |