Skip to main content Skip to search Skip to main navigation
Menu

APV Sägerät 500 l elektrisch, ISOBUS, 8 Ausgänge, 12 V

Skip product gallery

Zubehör / Ersatzteile

APV Verlängerungskabel Stromversorgung Gebläse PLUS (2 m) für Pneumatische Sägeräte PS
Prod. no.: APV-04100-2-004
Hersteller:

Regular price: €199.00
APV Verlängerungskabel Stromversorgung Gebläse PLUS (5 m) für Pneumatische Sägeräte PS
Prod. no.: APV-04100-2-014
Hersteller:

Regular price: €230.00
APV Verlängerungskabel PS MX (5 m) für Multidosierer MD
Prod. no.: APV-00410-2-149
Hersteller:

Regular price: €190.00
APV Verlängerungskabel PS MX (14 m) für Pneumatische Sägeräte PS
Prod. no.: APV-00410-2-150
Hersteller:

Regular price: €285.00
APV Abdrehtaster für Multidosierer MD
Prod. no.: APV-00410-2-185
Hersteller:

Regular price: €112.00
APV Oberlenkerhalterung incl. Oberlenker für PS 120–PS 500 für Pneumatische Sägeräte PS
Prod. no.: APV-04000-2-114
Hersteller:

Regular price: €368.00
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
APV Pflanzenschutzmittel-Prüfplakette (für Länder der Europäischen Union) für Pneumatische Sägeräte PS
Prod. no.: APV-00300-3-135
Hersteller:

Regular price: €97.00
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Description

Standard scope of delivery

  • Complete seeder with hoses (25 m)
  • Seed roller for fine seed and seed roller for coarse seed
  • Agitator
  • 6 m cable from the seeder to the control module
  • Wiring harness for the power supply to the PLUS fan
  • Calibration chute, counter plate, calibration bag, seed scales
  • Fill-level sensor
  • 8 deflector plates and 4 hexagonal bars, each 1.2 m long, for mounting the deflector plates
  • ISOBUS equipment

Technical data

ManufacturerAPV Technische Produkte GmbH
Product typePneumatic seeder
Hopper capacity500 l, plastic
FanElectric fan PLUS
OperationISOBUS
Working width1 – 6 m with 8 outlets
Optional working width1 – 12 m with 16 outlets
Fan current consumption12 V / 40 A
Seed roller drive current consumption12 V / 10 A
Power supplydirect from the battery
Dimensions (H × W × D)125 × 80 × 120 cm
Weight100 – 108 kg
Hoses25 m
Deflector plates8 pieces

Product description

Pneumatic seeder with 500 litres and ISOBUS

The machine accurately applies cover crops, undersown crops, grass overseeding and much more, regardless of the wind. It can be mounted on almost all soil cultivation equipment, seed drills and crop care equipment, regardless of the manufacturer.

Why pneumatic rather than broadcast

This is the fundamental difference compared with a broadcast spreader.

With a broadcast spreader, a rotating disc distributes the seed across the area. Wind alters the spreading pattern – light seeds travel further than heavy ones, and crosswinds shift the entire pattern.

With a pneumatic seeder, the seed is conveyed through hoses to fixed outlets and deposited there via deflector plates.

  • Unaffected by wind. The route from the hopper to the ground is enclosed.
  • Precise lateral distribution across the entire working width.
  • Consistent results. The spreading pattern does not depend on the weather.

This is particularly important with mixtures: A cover crop mixture contains seeds of very different weights. A broadcast spreader separates them over the throwing distance – the mixture at the edge differs from that in the middle.

The PLUS fan – how it differs from the basic version

This is the specification featured in this product.

Electric fanElectric fan PLUS
DesignTwin fanFan PLUS
Current consumption12 V / 25 A12 V / 40 A
Power supplyvia control moduledirect from the battery
Max. working width1 – 6 mup to 1 – 12 m possible
Application ratelowerhigher

Why direct battery power is necessary: 40 amps cannot be supplied via a control module. The required wiring harness is supplied with the PLUS fan.

Important before ordering: The alternator on the towing vehicle must provide sufficient power. The fan and seed roller drive draw up to 50 A combined – this should be checked on older tractors.

Choosing the right fan – how to calculate it

The manufacturer specifies a formula:

Working width (m) × speed (km/h) × sowing rate (kg/ha) ÷ 600 = kg/min

Required outputSuitable fan
up to 3.5 kg/minPS 120
up to 8 kg/minPS 200
up to 14 kg/minPS 300
up to 30 kg/minPS 500

A calculation example from the manufacturer: 45 kg/ha of cover crop mixture at 10 km/h and a 6 m working width gives 4.5 kg/min. A machine in the 200 to 500 class with a PLUS fan is sufficient for this.

When the 500 class is needed: high sowing rates, wide working widths or working at speed – and, above all, the large hopper, which needs refilling less often.

ISOBUS – operation via the tractor terminal

This is the second key feature of this product.

What ISOBUS offers: The seeder is operated via the existing ISOBUS terminal in the tractor – with no additional control module in the cab.

  • One display instead of two. No extra screen or additional cable on the dashboard.
  • Consistent operating logic with the other ISOBUS implements.
  • Data transfer. The speed signal and working position come from the tractor.
  • Documentation via the terminal.

The package price advantage: Retrofitting ISOBUS to the PLUS fan costs €1,480 when purchased separately. In the complete package, the surcharge compared with the version without ISOBUS is €1,480 – so there is no disadvantage, and installation is not required either.

Important: A control module is required if the tractor does not have an ISOBUS terminal. Check the tractor's ISOBUS equipment before ordering.

Speed-adjusted application

With sensors, the machine adjusts the seed rate to the forward speed.

Why this matters: Without adjustment, the quantity applied per hectare depends directly on the speed. If you slow down at the headland, twice as much is applied there – a real loss when using expensive seed.

Headland management switches off application at the end of the field and switches it back on when entering the field again.

Mounting on almost any carrier machine

The manufacturer explicitly states that it can be mounted on almost all soil cultivation equipment, seed drills and crop care equipment, regardless of the manufacturer.

Typical combinations: cultivator, disc harrow, power harrow, tine harrow, roller, seed drill.

Points to note when mounting:

  • Deflector plate mounting height: approx. 40 cm above the cultivated soil.
  • Deflector plate spacing: maximum 75 cm from centre to centre.

Why these measurements determine distribution quality: The deflector plate spreads the seed flow across the area. If mounted too high, the seed is caught by the wind – if the plates are too far apart, gaps form between the spreading patterns.

Two seed rollers included

A seed roller for fine seed and one for coarse seed are included as standard.

Why two are needed: The seed roller meters the seed. A grass seed and a field bean require completely different chamber sizes – a universal roller would meter one of them inaccurately.

For other applications, the manufacturer offers additional seed rollers.

The calibration kit – essential for applying the correct quantity

The calibration chute, counter plate, calibration bag and seed scales are included.

Why calibration is essential: Every batch of seed flows differently, depending on the variety, moisture, seed treatment and grain size. The factory setting is a guide, not a guarantee.

If you do not calibrate, you may apply 20% too much or too little. With cover crop mixtures, this either costs money or reduces crop density.

Standard fill-level sensor

It alerts you when the hopper is running low.

Why this matters with a 500-litre hopper: The hopper is behind the driver. Without a sensor, you may not notice that the hopper is empty until a pass has been left unsown – and it is difficult to make up properly afterwards.

Available with an EU inspection sticker

An inspection sticker is available for applying plant protection products in granular form (surcharge €97).

When is it required: Equipment used to apply plant protection products is subject to mandatory inspection. It is not required for seed and fertiliser applications alone.

Applications

Cover crop sowing, undersowing into standing crops, grass overseeding and grassland care, greening in vineyards and orchards, sowing on stubble fields, flower strips and ecological focus areas, agricultural contractors, arable farms.

Operating notes

  • Check the tractor's ISOBUS equipment before ordering – a control module is required if there is no terminal.
  • Check alternator output: the fan and seed roller drive draw up to 50 A combined.
  • Connect the wiring harness directly to the battery; use the cables supplied.
  • Mount the deflector plates approx. 40 cm above the cultivated soil, with a maximum centre-to-centre spacing of 75 cm.
  • Calibrate before every seed change – the calibration kit is included.
  • Choose the seed roller to suit the type of seed.
  • When applying plant protection products, observe the requirements for professional competence and mandatory inspection.
  • Empty and clean the hopper after use – residual seed absorbs moisture and clogs the metering system.
  • Check the hoses for kinks and blockages.
  • Store the machine in a dry, frost-free place.
  • Follow the manufacturer's operating instructions.

Frequently asked questions

Do I need an additional control module?

No, this machine is equipped for ISOBUS and is operated via the tractor terminal. A control module would be required if the tractor does not have an ISOBUS terminal.

What is the difference between the PLUS fan and the standard fan?

It draws 40 A instead of 25 A, is powered directly from the battery and enables working widths of up to 12 m with 16 outlets. The power supply wiring harness is included.

What working width is possible?

1 to 6 m with the standard 8 outlets. Optionally, 1 to 12 m with 16 outlets is possible using Y-splitters or doubling pieces.

Will the machine fit my implement?

It can be mounted on almost all soil cultivation equipment, seed drills and crop care equipment, regardless of the manufacturer. The deflector plates should be positioned approx. 40 cm above the cultivated soil, with a maximum centre-to-centre spacing of 75 cm.

How much power does the machine need?

The fan requires 12 V / 40 A and the seed roller drive 12 V / 10 A. The towing vehicle's alternator should be rated accordingly.

Why choose pneumatic rather than a broadcast spreader?

The seed is conveyed through hoses to fixed outlets – application is unaffected by wind and even across the entire working width. With mixtures, this prevents the seeds from separating over the throwing distance.

Do I need to calibrate the machine?

Yes, before every seed change. Every batch flows differently, depending on the variety, moisture, seed treatment and grain size. The calibration chute, counter plate, calibration bag and seed scales are included.

What are the machine's dimensions and weight?

125 × 80 × 120 cm (H × W × D), with a weight of 100 to 108 kg. The hopper holds 500 litres.