ALÖ Quicke Silage fork M+ with grab 2430 mm, 1.27 m³ - Euro mounting bracket
€3,205.00
Scope of delivery
- 1 × silage fork with grab, working width 2,430 mm
- 13 bottom tines and 13 grab tines, tine spacing 20 cm
- 2 hydraulic cylinders, reinforced grab design
- Euro-standard mounting
Not included – check before ordering:
- 200 bar pressure relief valve – required if your loader’s hydraulics deliver more than 200 bar
- Load-holding valve for grab attachments – prevents the grab from opening if a hose or line fails
- Hydraulic hoses and couplings, multi-coupler
- Edge protection strip
Technical data
| Manufacturer | Ålö AB, Sweden (Quicke brand) |
|---|---|
| Type | Silage fork with hydraulic grab |
| Size model | 250 |
| Working width | 2,430 mm |
| Overall width | 2,530 mm |
| Working depth | 880 mm |
| Overall length | 1,100 mm |
| Overall height, closed | 930 mm |
| Overall height with grab open | 1,460 mm |
| Maximum opening | 1,190 mm |
| Volume | 1.27 m³ |
| Bottom tines | 13, spacing 200 mm |
| Grab tines | 13, spacing 200 mm |
| Tine design | curved, Conus 1 (bottom and grab) |
| Hydraulic cylinders | 2 |
| Maximum hydraulic pressure | 210 bar |
| Mounting | Euro-standard |
| Weight | 441 kg |
Product description
A silage fork with grab picks up what a bucket cannot handle cleanly: silage from the freshly cut face, manure from the pen, round bales and bulky material. The bottom tines move in, the grab comes down from above, and the material is clamped rather than pushed.
With a working width of 2.43 m and a weight of 441 kg, this attachment is designed for farm loaders, compact wheel loaders and medium-sized telehandlers.
Curved tines – and why this is more than a matter of shape
The tines are curved and follow an arc through the material as they enter. This differs from straight tines, which penetrate linearly:
- The material is cut, not torn. A curved movement severs the fibres; a linear movement pushes them apart.
- Less force is required. Less resistance means that even a farm loader with limited hydraulic capacity can use the full width.
- The tines last longer. Cutting rather than bending means less material fatigue at the tine base.
But the most important point is not in the data sheet: it is the silage face.
A torn silo face is loose and rough. Air gets into this loosened layer – and air in the silo means secondary fermentation, heating, mould and dry matter loss. If the face remains open for several days until the next layer is removed, this adds up to real feed losses.
A smooth face is therefore not about appearance, but feed quality. This is the strongest argument for this design over a bucket.
The material is pressed against the back wall
When the tines close, the load is pressed against the back wall of the attachment and held there. It may sound like a minor detail, but it saves time every day:
On uneven farmyards, over the silo edge, over the threshold to the feed passage – at each of these transitions, an open attachment loses material. Anything that falls ends up in the yard, gets driven over, heats up and has to be swept up. A clamped load stays where it is.
20 cm tine spacing
With 200 mm spacing and 13 tines across 2.43 m, this attachment has closely spaced tines. This design is for short-chopped maize silage, which would fall through more widely spaced tines.
To be fair: Closely spaced tines require more force to penetrate than widely spaced ones, and are more likely to clog with long-fibred, strawy manure. The close spacing is right for predominantly silage use; if you handle long-straw manure 90% of the time, wider spacing will make the job easier.
Reinforced grab and two cylinders
The larger sizes in this range – including this one – have a reinforced grab mechanism and larger-diameter cylinders. This is necessary at a width of 2.43 m: the clamping force must extend across the full width, not just the centre, or the load will slip out at the sides.
The maximum opening of 1,190 mm determines what will fit. In practice, round bales with a diameter of 1.20 m will just fit; larger ones will not. If you want to handle bales, measure yours.
Hydraulics: 210 bar is the upper limit
The maximum permitted hydraulic pressure is 210 bar. This is not a comfortable margin on modern loaders, but a limit that must be checked – many tractors and loaders operate at system pressures of 200 to 250 bar.
If your hydraulics deliver more than 200 bar, a pressure relief valve is required. It is available as an accessory. Check your machine’s system pressure before ordering – an overloaded cylinder is not covered by the warranty.
The attachment requires a double-acting spool valve to open and close the grab.
The load-holding valve – the accessory you should not leave out
A hydraulic grab holds its load using oil pressure. If the pressure is lost – due to a burst hose, leaking coupling or broken line – the grab opens.
With nearly a tonne of silage at head height, this is no theoretical risk. The load-holding valve, available as an accessory, shuts off the oil in the cylinder and holds the load even if a line fails. On an attachment of this size, it should be standard equipment, not an optional extra.
What the loader has to carry
Do the sums before ordering. The attachment weighs 441 kg empty, and 1.27 m³ of silage weighs 825 to 950 kg, depending on the material and how tightly it is packed.
That is around 1,300 to 1,400 kg at the attachment point – at an overall length of 1.10 m, giving it a significant forward leverage. What matters is your loader’s lifting capacity at full lift height, not at ground level: capacity is lowest there, and that is where you load the feed passage or trailer.
The Euro-standard mounting
The Euro-standard mounting is the most widely used system on front loaders and farm loaders. This means the attachment fits the vast majority of machines in this class without an adapter.
The same range is also available with other mounting systems – each is a separate product with its own number. Check the mounting on your machine and select the correct product; conversion is not предусмотрed.
Tines as wear parts
The tines are fitted into box sections with welded sleeves and can be replaced individually. This is the right design for an attachment that works against the silo wall every day: a bent or broken tine is a spare part, not damage to the attachment.
The bottom and grab tines are Conus 1 design – replacement tines must match this specification.
Frequently asked questions
What lifting capacity does my loader need?
Allow for around 1,300 to 1,400 kg: 441 kg tare weight plus 825 to 950 kg of silage at 1.27 m³. The key figure is the lifting capacity at full lift height, not at ground level – and with an overall length of 1.10 m, the load centre is well forward of the mounting.
Do I need a pressure relief valve?
Yes, if your loader’s hydraulics deliver more than 200 bar. The attachment’s maximum permitted pressure is 210 bar. As many modern loaders operate at 200 to 250 bar, the valve is often essential rather than optional. It is available as an accessory.
What is the load-holding valve for?
It shuts off the oil in the cylinder so that the grab does not open and drop its load if a line fails. It is highly recommended for an attachment carrying nearly a tonne of material at head height.
Will round bales fit in the grab?
The maximum opening is 1,190 mm. Bales with a diameter of 1.20 m will just fit; larger ones will not. Measure your bales if this is a main application.
Why are the tines curved?
As they enter, they follow an arc and cut the material rather than tearing it. This reduces the force required, extends tine life and, most importantly, leaves a smooth silo face – reducing air ingress, secondary fermentation and feed losses.
Is the 20 cm tine spacing suitable for manure?
Yes, but the close spacing is optimised for short-chopped silage, which would fall through wider gaps. It requires more force to penetrate predominantly long-fibred strawy manure; if you handle almost exclusively this type of material, wider spacing will make the job easier.
Will the attachment fit a mounting other than Euro-standard?
No. This product has a Euro-standard mounting. The same range is available with other mounting systems, each as a separate product. Conversion is not предусмотрed.
Are hydraulic hoses and couplings included?
According to the manufacturer’s documentation, hoses, couplings and a multi-coupler are listed as accessories. Please confirm the scope of delivery when ordering and select the coupling system that matches your machine.
Can individual tines be replaced?
Yes. The tines are fitted into box sections with welded sleeves and can be replaced individually. Replacement tines must match the Conus 1 design.
| Gerätetyp : | Silagegreifer |
|---|---|
| Recording: | Euro borrowing |
| Working width: | 2.50m |